Weights And Dimensions; Optional Accessories - Gemini CS-02 Manuel

Masquer les pouces

Table Des Matières

Table des Matières

Les langues disponibles

(63).

UTPUTS

30. M

(32): This switch toggles whether the

ONO

UTPUT

WITCH

(59, 60) will be in Mono or Stereo.

ASTER

UTPUTS

31. A

BPM/T

(33): This button controls the BPM

UTO

UTTON

detection engine. By pressing and holding this button for 1 sec-

onds, the unit will attempt to automatically detect the beats per

minute of the audio channel which is selected via the C

(13). If there is no channel selected, the unit will attempt to

UTTON

detect the BPM of the Master signal. If the unit is not able to accurately

detect the BPM, you may tap the A

BPM/T

UTO

music until the correct BPM is displayed on the LCD P

(36). To show the BPM at any time, press the A

momentarily, and it will again be displayed on the LCD P

(36). When the letters 'A BPM' are displayed with the beats per minute, it

indicates that the value displayed was automatically detected. When the

letters 'T BPM' are displayed with the beats per minute, it indicates that

the value displayed was calculated via the TAP function.

32. EFX-T

(34): When this feature is turned on,

EMPO

YNC

any effects that can be synchronized to tempo will be linked to the

tempo that is set via the A

BPM/T

UTO

UTTON

33. T

(35): This selector controls the ratio of

EMPO

ATIO

ELECTOR

the tempo that is set via the A

BPM/T

UTO

the control is set to any other value other than 1 (1:1 ratio), the

tempo will be multiplied by that value. For instance, if a track is 125 beats

per minute, then switching the T

EMPO

ATIO

ratio, and the effect would be applied at 250 beats per minute. If the

is set to 1/2, it would be a 1:2 ratio, which means

EMPO

ATIO

ELECTOR

the effect would be applied at 62.5 beats per minute.

34. LCD P

(36): This blue backlit display

ARAMETER

ISPLAY

shows the effect name and parameter that is relative to the

effect. It also shows the detected BPM, when applicable.

35. M

(37): These banks are useful

EMORY

ECALL

ANKS

for memorizing effect settings during a performance. By

pressing and holding any one of the numbered buttons for 2 seconds,

you can memorize all of the effects settings that are currently in place,

including Channel, BPM, Tempo Ratio, Tempo Sync On/Off,

Parameter, and EFX On/Off. Once you have memorized settings into a

recall bank, it can be recalled by simply pressing the button momentarily.

36. EFX P

(38): This rotary control selects the

ROGRAM

ELECTOR

DSP effect which will be applied to the audio, when engaged.

37. EFX P

(39): This slide control allows

ARAMETER

ONTROL

you to alter the parameter associated with the DSP effect.

38. EFX D

(40): This rotary control allows you to

ONTROL

alter how much of the audio signal is sent through the DSP effects

section. For less intense effects, turn the control towards 'Dry'. For more

intense effects, turn the control towards 'Wet'.

39. EFX O

(41): By pressing this button, the DSP

UTTON

effect that is selected is turned On or Off.

EPLACING THE

1. Remove the black brushed aluminum plate which outlines the Channel

and X-Fader section. The screws can be found at each corner of this plate.

2. To remove a channel fader, simply remove the two screws on the top and

bottom of the fader. Disconnect the connector which plugs into the bottom

of the fader, and replace it with a new fader. Verify that the fader is facing

EFX A

HANNEL

SSIGN

the appropriate direction before screwing it back in.

3.To replace the X-Fader, first unscrew the two outermost screws from the

in time to the

UTTON

X-Fader, and disconnect the connector which plugs into the bottom of the

ARAMETER

ISPLAY

fader. Remove the two innermost screws on the front of the fader, to

BPM/T

(33)

UTO

UTTON

remove the steel limiting plate. Attach the limiting plate to the new replace-

ARAMETER

ISPLAY

ment X-Fader (model RG-45 or RG-45PRO). Then, replace the connector

which plugs into the bottom of the fader, and replace the fader in the

appropriate direction before screwing it back in.

SER

EPLACEABLE

User replaceable parts are listed below, and may be obtained by calling

your nearest Gemini office, listed on the back cover page of this manual.

(33).

CROSSFADER: RG45 OR RG-45PRO

(33). When

CHANNEL FADER: 072-127

UTTON

CHANNEL AND X-FADER KNOB: 002-742

PARAMETER CONTROL FADER KNOB: 002-741

to 2 would be a 2:1

ELECTOR

GROUND TERMINAL: 146-710

SPECIFICATIONS

Inputs:

Phono.....................................................................................3 mV, 47 KOhm

Line....................................................................................150 mV, 27 KOhm

MIC 1, MIC 2, MIC 3..........................................1.5 mV, 1 K Ohm Balanced

MIC 1 High.........................................................................................± 12dB

MIC 1 Mid..........................................................................................± 12dB

MIC 1 Low..........................................................................................± 12dB

Talkover Attenuation.............................................................................-16dB

Outputs:

Master/Zone/Booth RCA....................................................0 dB 1V, 400 Ohm

Max......................................................................................20V Peak-to-Peak

Record..................................................................................225 mV, 5 KOhm

Balanced Master...........................................................2V, 400 Ohm

General:

Frequency Response.................................................20Hz - 20KHz +/- 2 dB

Distortion.........................................................................................< 0.02%

S/N Ratio...........................................................................Better Than 80 dB

Headphone Impedance.....................................................................16 Ohm

Power Source..........................................................115/230V, 60/50Hz, 20W

X-F

ADER AND

HANNEL

ADERS

ARTS

<7>