Before Use; Instructions Foruse Of The Equipment; Holding The Hedge Trimmer When In Use; Optimum Safety - IKRA HHSI 5546 Hurricane Manuel D'utilisation

Before use

Optional: Assembly of the protection shield (Fig. 2)
Slide the included protection shield (3) over the blade rail
and fix it from both sides at the housing using 2 screws
on each side as shown in Fig. 2.
Power connection
The machine can only be connected to a single-phase
a.c. current connection. The machine is protectively in-
sulated in accordance with classification II of VDE 0740.
Before using the machine ensure that the mains current
agrees with the operating voltage data on the machine's
identification plate.
Power Circuit Breaker:
Machines which will be used in different outside loca-
tions must be connected to a Power Circuit Breaker.
Securing the power supply cable (Fig. 3)
Only use cables (extension flex) that are approved for
outdoor use. The cable diameter must be equal to or bigger
than 1.5mm² for cable lengths up to 75m.
Put the coupling of the extension flex onto the shears'
plug. For strain relief, stick a loop of the extension flex
through the opening in the handle and put it onto the
strain relief hook.
Extension flexes with a length of more than 30m reduce
the machine's output.
Instructions for use of the equipment
Do not use the trimmer in rain or for cutting wet
hedges!
Check the hedge trimmer flex and its connections be-
fore each and every use for visible signs of damage
(disconnect the power plug)! Do not use a faulty flex.
Gloves:
Protective gloves must be worn when using the
hedge trimmer.
Switching the hedge shears on/off
When switching the hedge shears on take a safe stand.
These hedge shears have a two-hand safety switch. To
switch the hedge shears on the bar switch in the handle
(A) and the grip switch of the bow-type handle (B) must
be pushed down. To switch the device off let go of both
switches. The motor already stops if one of the two
switches is released.
The breaking mechanism causes the blade to stop within
0.5 sec. The sparks (flashes) developing from this in the
area of the upper ventilation slots are normal and harm-
less for the device.
Maintenance
Always disconnect the plug from the power socket
before commencing any work on the machine.
GB | Operating Instructions
Important: Always clean and oil the blades after pro-
longed use of the hedge trimmer. This will greatly affect
the life of the equipment. Damaged cutting units must be
properly repaired immediately. Clean the shearing blades
with a dry cloth or – in case of heavier dirt – with a brush.
Attention: Danger of injury! Oiling of the blades should
ideally be carried out using an environmentally friendly
lubricant (Fig. 7).
Sharpening of the blades
The blades generally do not need servicing and do not
require resharpening if used correctly.
Changing the blades
Only correct installation of the blades will guarantee
problem-free operation and function of the above men-
tioned safety feature of the blades. Changing of the
blades should therefore only be carried out at a specialist
workshop.

Holding the hedge trimmer when in use

This equipment will enable you to cut or trim bushes and
hedges easily and comfortably.
Trimming of hedges
- Young shoots are best cut in a scythe movement.
- Older and stronger hedges are best cut in a sawing
- Branches, which are too thick for the hedge trimmer,
- Sides of hedges should be cut upwards in a taper.
In order to achieve an even height
- Fix a guide line at the required height.
- Cut evenly over this guide line.
Take care to have a secure and safe standing position
when working with your hedge shears in order to avoid
slipping and injury. Always keep the shearing blades
away from your body.

Optimum safety

(Fig. 4) The 5 special features two-hand safety switch, quick
blade stop, protective cover, blade safety rail and impact
protector are fitted to provide the hedge trimmer with
optimum safety features.
Two-hand safety switch (Fig. 4)
To switch the hedge shears on the bar switch in the
handle (A) and the grip switch of the bow-type handle (B)
must be pushed down. To switch the device off let go of
both switches. The motor already stops if one of the two
switches is released.
GB-5
movement.
should be cut with a saw.
Attention!
If you find out that safety functions, such as
the 2-switch mechanism or the safety stop, are
not functioning while working with the hedge
shears, immediately cease working and take
the machine to a specialised shop for repairing.
(Fig. 5)