Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 24
- Impact drilling - for drilling masonry, concrete,
etc.
- Hammer mode - for chiselling and demolition.
For operation without fatigue during chiselling
and demolition, the accessory can be fitted and
fixed (at intervals of 8 degrees) in the desired
angular position (see "Changing the chisel posi-
tion").
Turn the operation mode switch 6 to the desired
position:
(1) - Impact drilling
(2) - Changing the chisel position
(3) - Hammer mode
INSERTING Of SDS-MAx TOOL
Clean and grease the shank of the accessory,
before placing it into the socket!
Keep the locking socket 2 in upper (front) posi-
tion while inserting the tool.
Place the tool into the spindle without effort.
Rotate the tool until the grooves coincide.
After the grooves have coincided, push the tool
down (until the fixing mechanism produces an
audible "click"). Check the proper fixing of the
tool by pulling it strongly outwards.
WARNING: For operating with chisels
switch 6 shall always be in "hammer" posi-
tion.
REMOVING THE SDS-MAx TOOL
Pull the locking clutch entirely back and take the
tool out.
CHANGING THE CHISEL POSITION
- Insert the tool in the socket as it is described in
point "Inserting the SDS-max tool".
- Turn the operating mode switch 6 in position
"Changing the chisel position".
- Turn the tool by hand to the desired position.
- Turn the operating mode switch 6 in position
"hammer", and then turn the tool slightly left wise
and right wise until it is locked.
Longer operation life of the rotary hammer and
higher efficiency can be achieved only with well-
sharpened tools for demolition and chiselling.
AUxILIARY HANDLE
Always use the auxiliary handle.
Loosen the handle by turning it left wise. Turn
the handle in the most convenient for operation
position, and then tighten it well.
8
EN
Do not carry the machine by a loose auxiliary
handle.
You can fix the drilling depth through depth
gauge 4. The depth gauge 4 can be fixed by
screw 3.
The auxiliary handle for these models is con-
nected to the body of the machine through vi-
bration dampers, protecting the operator and
reducing fatigue.
RECOMMENDATIONS fOR
OPERATION
Apply moderate pressure during operation (ap-
proximately 150-200 N)! Higher pressure will not
increase efficiency when drilling and chiselling,
but it will lead to decreasing the operation life of
the machine.
Take the drill bit out of the opening from time to
time to remove dust.
Watch out for the stage of bit blunting and re-
place the bit when considerable decrease of ef-
ficiency is observed.
ACCESSORIES
▪ SDS-max twist drill bits for concrete Ø12 to
Ø50 mm. We recommend operation with Ø24
to Ø40 drill bits, for the optimum operation the
machine is designed for.
▪ SDS-max break through drill bits for concrete
up to Ø80 mm
▪ SDS-max core cutters up to Ø100 mm
▪ SDS-max point chisels up to 600 mm long
▪ SDS-max flat chisels up to 80 mm wide
▪ SDS-max groove chisel up to 32 mm wide
WARNING: We recommend using
these accessories or attachments when op-
erating your power tool. The use of any other
accessories or attachments might present a
risk of injury. Only use accessory or attach-
ment for its stated purpose. If you need any
assistance for more details regarding these
accessories, ask your local SPARKY service
centre.

Maintenance

WARNING: Always ensure that the
tool is switched off and unplugged before
attempting to perform inspection or mainte-
nance.
BP 750CE

Publicité

Table des Matières
loading

Table des Matières