Dmx Mode - Laserworld Proline Série Mode D'emploi

Manual
ILDA mode
When an ILDA compatible interface is connected to the laser, the laser is automatically switched to ILDA mode.
Output is then controlled from a PC running software. The laser uses pins 4 and 17 of the ILDA signal to detect
the presence of an ILDA interface. Further information can be found in the software manual.
Please note: the scanners are set to a scanspeed of ca. 22000 PPS at ca. 30° scanangle. If you increase the
scanspeed, first reduce the scanangle (image size). Otherwise you may damage the scanners! When using with
different scanspeed/scanangle readjustment of the scanner drivers may be necessary, if in doubt, contact your
dealer.

DMX mode

Channel
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Maintenace / cleaning
Always disconnect from mains before cleaning/opening the laser. You can open the device by removing the top:
remove the mounting bracket (4 quick locks), the 5 Philips screws, and the eye bolt.
Regularly clean the interior from dust, especially ensure operation of the fans. To clean the mirrors, ideally use
acetone and lens cleaning paper (fold paper to get an edge with which to clean the mirrors). If not available, you
can also use window cleaner, and a paper towel. Be careful, even light scratches reduce the output power of the
laser; always clean with strokes in one direction, to minimize the effect of scratches. Mirrors need cleaning, when a
"halo" is noticeable around the beam, or an unusual high amount of diffuse light can be seen inside the device.
When fog fluid condenses in the device, clean all traces, and rearrange the position of fazer and/or laser.
Technical specifications
 Output power (in mW, at the laser):
Power max. Power/wavelength green Power/wavelength red
Pro-1200 G 1200
Pro-2000 G 2000
Pro-3500 G 3500
Pro-6000 G 6000
Pro-700 RGB 700
Pro-1700 RGB 1700
Pro-1700 RGB UPG 900
Pro-3100 RGB 3100
Pro-3100 RGB UPG 1500
Pro-6000 RGB 6000
Pro-6000 RGB UPG 3300
Red
Green
Blue
Colour
Pattern group
Pattern
Horizontal rotation
Vertical rotation
Rotation about Z-axis
Horizontal movement
Vertical movement
Horizontal size
Vertical size
Hor. and vert. size
Drawing speed
Point draw
Scanspeed
Pattern size
>800 532nm
>1200 532nm
>2500 532nm
>4500 532nm
>100 532nm
>250 532nm
>250 532nm
>500 532nm
>500 532nm
>1200 532nm
>1200 532nm
DMX512 value
0~255 0~100% Dimmer
0~255 0~100% Dimmer
0~255 0~100% Dimmer
0~25 Original colour
26~51 White
52~77 Yellow
78~103 Red
104~129 Green
130~155 Cyan
156~181 Blue
182~207 Purple
208~233 Change colour
234~255 Colour flux, slow to fast
0~51 Pattern group 1
52~103 Pattern group 2
104~154 Pattern group 3
155~205 Pattern group 4
206~255 Pattern group 5
0~255 160/5=32pcs
0~255 slow to fast
0~255 slow to fast
0~255 slow to fast
0~255 slow to fast
0~255 slow to fast
0~255 slow to fast
0~255 slow to fast
0~255 slow to fast
0~255 slow to fast
0~255 slow to fast
0~255 slow to fast
0~1 Original size
2~255 Size (120=original)
>280 655nm
>700 655nm
>150 640nm
>1500 655nm
>300 640nm
>2500 655nm
>500 640nm
Function
Power/wavelength blue
>70 473nm
>150 473nm
>150 473nm
>200 473nm
>200 473nm
>350 473nm
>350 473nm
Revision: Apr-10
4 / 14
Beam
3mm/1mrad
3mm/1mrad
3mm/1mrad
3mm/1mrad
3mm/1mrad
3mm/1mrad
3mm/1mrad
3mm/1mrad
3mm/1mrad
3mm/1mrad
3mm/1mrad