General Safety - Silverline 30-135A Mode D'emploi

380736
Technical Abbreviations Key
V Volts
~, a.c. Alternating current
A, mA Ampere, milli-Amp
Ø Diameter
Hz Hertz
, d.c. Direct current
W, kW Watt, kilowatt
Specification
Input voltage:............................................................................230V~ 50Hz
Input current: ....................................................29.4A (peak), 12A (average)
Efficiency: ................................................................................................80%
Output current range: ...........................30-135A (30, 43, 52, 78, 105, 135)
Rated duty cycle: .................................10%@135A, 60%@43A, 100%@30A
No load output voltage: ...........................................................................37V
Output voltage: ............................20.75V(135A), 16.15V(43A), 15.5V(30A)
Insulation class: .......................................................................................... H
Ingress protection: ............................................................................... IP21S
Wire: ............................................................................................ 0.6-0.8mm
Welding thickness range (steel): ..............................................1.2 – 6.5mm
Mains circuit breaker fuse: ...........................................................32A or 30A
Protection class: ....................................................................................
Torch cable length: ....................................................................................2m
Earth cable length: ................................................................................ 1.5m
Gas tube: ............................................................................................ Ø4mm
Power cable length: ..................................................................................2m
Dimensions (H x L x W): ............................................... 680 x 300 x 500mm
Weight: ............................................................................................ 24.85kg
As part of our ongoing product development, specifications
of Silverline products may alter without notice.
MIG/MAG Combination Gas/No Gas Welder

General Safety

WARNING: Read this manual before operating, adjusting and servicing this welder.
WARNING SIGHT RISK: Arc glare can permanently damage your eyesight. Always use a
suitable welding mask, face shield or helmet. Always check condition of eye protection before use.
WARNING: FIRE RISK: All flammable materials must be removed from the welding area.
WARNING: WELDING FUMES: Toxic gases are given off during welding. Always use in a
well-ventilated area.
WARNING: BURN RISK: Wear welding gloves at all times when welding. They will reduce
the risk of burn injuries and ultra-violet radiation. In addition, wear a leather apron to protect from
spatter and a cap when welding overhead.
WARNING: This appliance is not intended for use by persons (including children) with
reduced, physical or mental capabilities or lack of experience or knowledge unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children must be supervised to ensure that they do not play
with the appliance.
Keep work area clear - Cluttered areas and benches invite injuries
• Consider work area environment
- Do not expose welder to rain
- Do not use welder in damp or wet locations
- Keep work area well lit
• Keep other persons away. Do not let persons, especially children, not involved in the work touch
the tool or the extension cord and keep them away from the work area
WARNING: Not using protective equipment or appropriate clothing can cause personal
injury or increase the severity of an injury.
• Do not abuse the power cable. Never pull the power cable to disconnect it from the socket.
Keep the power cable away from heat, oil and sharp edges. Damaged or entangled power cables
increase the risk of electric shock
• Do not overreach. Keep proper footing and balance at all times
• Maintain tools with care
- Inspect tool power cables periodically and have them repaired by an authorised service facility
if damaged
- Inspect extension cables periodically and replace if damaged
• Disconnect - Disconnect welders from the power supply when not in use, before servicing and
when changing accessories
WARNING: The use of accessories or attachments not recommended by the manufacturer
may result in a risk of injury to persons.
• Stay alert
- Watch what you are doing, use common sense and do not operate the tool when you are tired
- Do not use a welder while you are under the influence of drugs, alcohol or medication
WARNING: A moment of inattention while operating power tools may result in serious
personal injury.
• Check damaged parts
WARNING: Do not use the welder if the on/off switch does not switch the tool on and off.
The switch must be repaired before the welder is used.
• Have your tool repaired by a qualified person. This welder complies with the relevant safety
rules. Repairs should only be carried out by qualified persons, otherwise this may result in
considerable danger to the user
WARNING: When servicing use only identical replacement parts.
WARNING: If the power cable is damaged it must be replaced by the manufacturer or an
authorised service centre.
WARNING: Power tool mains plugs must match the mains socket. Never modify the plug in
any way. Do not use any adaptor plugs with earthed (grounded) power tools. Unmodified plugs and
matching sockets will reduce risk of electric shock.
silverlinetools.com
7