Publicité
Les langues disponibles
Les langues disponibles
Mirror Mounting Instructions:
For your specific vehicle configuration listed on page 2, position - clamp and fasten the
1.
assembled mirror onto the vehicle in desired location. If using the tube clamp, the flat
bracket (item #7) attaches to the bottom plastic clamp (item #8) using the two thread
forming screws (item #13) as shown. (See illustration 2-1).
positioned onto the plastic clamp in multiple orientations.
please use the pan screws (item #12) and small locknuts (item #11) for fastening as
shown. (See illustration 2-2).
Tighten the screws to specified torque setting. WARNING: Do not over tighten hardware or
2.
damage can occur.
Torque Charts:
Tighten all screws to their specified torque values listed in below table.
Item
N*m
kgf*m
2
13.6
1.4
10
5
0.5
12, 13
1.4
0.1
the clamp arms (items #3 and #4) can allow mirror (item #1) to become disconnected
from the ball studs - please support mirror while making adjustments.
Use and Care Information:
Check the accessory mounts frequently and retighten if necessary.
•
Replace this accessory with a new one if it is damaged or discolored excessively.
•
When this accessory becomes dirty, rinse it thoroughly with cool water to remove loose
•
dirt, then wipe with a clean cloth or sponge. Never use petroleum solvents such as
gasoline, thinner, benzene, acid or alkaline cleaners.
Rearview mirror is not intended for on-road use.
•
For additional assistance, please contact Kolpin technical service department at
(877) 956-5746 or (763) 478-5800 or email
SPARE KITS
Item
Description
Threaded Ball Stud
2
Thumb Screw
5
Hex Locknut, Zinc Plated, M6-1.0
6
Socket Screw, Zinc Plated, M6-1.0 x 40mm LG
10
Locknut, Zinc Plated, #8-32
11
Pan Screw, Zinc Plated, #8-32 x 0.5in LG
12
Thread Forming Screw for Plastic Clamp
13
For the period of one (1) year from the purchase date, Kolpin will replace for the original purchaser, free of charge, any part or parts found
All transportation costs incurred submitting product to Kolpin for warranty consideration must be borne by the purchaser. If Kolpin
determines that the product must be returned to the factory for credit, please call 1-877-956-5746 for a Return Merchandise Authorization
This warranty does not apply to parts that have been damaged by accident, alteration, abuse, improper maintenance, normal wear, or
other causes beyond the manufacturer's control. In order to protect you and your ATV, certain parts of the accessory system and/or
hardware are designed to fail when the equipment is over-stressed. Parts that are lost due to loosening and improper maintenance are not
covered under warranty. This warranty does not cover removal or reinstallation labor fees of the plow system and related components.
Peripheral products such as engines, electric motors, and actuators may carry an original manufacturer's warranty. Most hardware is
general in nature and is easily obtained locally. Be sure to replace with minimum metric class 8.8 specification.
3.
Pivot mirror to desired viewing angle by
lbf*ft
loosening (turn counter-clockwise) the thumb screw
10
(item #5) and then tighten (turn clockwise) to secure
4
into position as shown. (See illustration 2-3).
1
the thumb screw (item #5) is loosened too much,
customerservice@kolpin.com
Hardware &
clamp kit P/N:
One Year Limited Warranty
upon examination by Kolpin to be defective in material, workmanship, or both.
(RMA) number and shipping instructions.
© 2017 Kolpin Outdoors Inc.
Note, the flat bracket can be
If using the flat bracket only,
Note, if
98301
1x
1x
1x
2x
2x
2x
2x
3
REV 00
Ill. 2-1
13
Ill. 2-2
12
11
5
1
Ill. 2-3
Publicité
