Using The Rangetop - hestan KRD Manuel D'utilisation Et D'entretien

USING THE RANGETOP

BURNER CONTROL KNOBS BURNER CONTROL KNOBS
Each sealed burner has its own control knob. The symbol
below each knob indicates which burner is controlled by each
knob. Push and turn LEFT (counter-clockwise) to HI to ignite
the flame, then turn to the desired flame setting.
SMART BURNER SMART BURNER CONTROL KNOB CONTROL KNOB
TM TM
The Smart Burner features a special control knob which
TM
communicates with Hestan Cue cookware via
wireless technology. This feature provides a unique
thermostatic control of the heating, as well as traditional
manual heat control for Cue and non-Cue pans. Please read the
Smart Burner TM section of this manual for more information.
BURNER TYPES & OUTPUT BURNER TYPES & OUTPUT
This table indicates the type and
output of each sealed burner. Dual-
flow burners have an inner and outer
row of ports, with a simmer function.
The single-flow burner (some models)
is similar to a commercial burner and
features very high output, and a low,
but no simmer function.
RE-IGNITION RE-IGNITION
Each sealed burner has its own electronic spark-ignition module with flame-sensing technology and
automatic re-ignition capability. If any burner should blow out, the igniter automatically re-lights the
burner.
Each burner should light in less than 4 seconds. Once lit, the sparking will stop. On very low simmer,
an occasional sparking may occur. This is usually due to a breeze in the room. If an igniter continues to
spark even with a flame present, there could be an electrical wiring issue, or some other problem. See the
TROUBLESHOOTING section of this manual for more information.
Note: The Smart Burner TM
gas will flow during this self check process. Sparking should not exceed 4 seconds.
DO NOT touch the burner or the igniters while sparking is occurring. A shock hazard or burns could
occur.
MANUAL LIGHTING / POWER FAILURE MANUAL LIGHTING / POWER FAILURE
THE OVEN, GRIDDLE, AND SMART BURNER
Each sealed burner can be manually lit in the event of a power failure. It is necessary to light each burner
individually.
If a power failure occurs WHILE you are using the sealed burners, turn all the knobs to the OFF position -
then light manually with a match or fireplace lighter.
Position the match or fireplace lighter at the port nearest the igniter, then turn the knob to HI until the
flame is lit. Wait until the flame has lit all the way around the burner before adjusting the knob to LOW
or SIMMER.
IF YOU SMELL GAS, turn all control knobs to OFF - check the precautions listed in the SAFETY section
of this manual.
Bluetooth
DUAL-FLOW
(FRONT)
HI
LOW
SIMMER HI
SIMMER LOW
DUAL-FLOW
(FRONT)
HI
LOW
SIMMER HI
SIMMER LOW
may take longer to light as the system runs a self check prior to ignition. No
CANNOT BE USED DURING A POWER FAILURE.
TM
®
BURNER OUTPUT - NATURAL GAS
OUTPUT DUAL-FLOW OUTPUT
(BTU/hr) (REAR) (BTU/hr)
23000 15500
HI
4200 4200
LOW
1500 1500
SIMMER HI
500 SIMMER LOW 500
BURNER OUTPUT - PROPANE
OUTPUT DUAL-FLOW OUTPUT
(BTU/hr) (REAR) (BTU/hr)
23000 HI 15500
4200 LOW 4200
1500 1500
SIMMER HI
600 600
SIMMER LOW
© 2021 Hestan Commercial Corporation
SINGLE OUTPUT
FLOW (BTU/hr)
30000
MAX
4200
LOW
SMART
20000
BURNER TM
GRIDDLE 15000
SINGLE OUTPUT
FLOW (BTU/hr)
MAX 22000
4200
LOW
SMART
20000
BURNER TM
GRIDDLE 15000
17
EN