Deleting A User Finger; Delete All; Factory Reset - Inokey system BT 502 Instructions D'utilisation

When he/she is identified, the green LED flashes and buzzer
buzzes one time. Blue LED flashes fast. Choose the relay, green
LED will follow.
•
The blue and green LEDs will flash alternately. At this point
the user presses his/her finger on the sensor three times. Af-
ter each successful sensor reading, short buzz will be heard. If
sensor reading is not successful (sensor area coverage is too
small), red LED will flash for 1 s.
•
When the user is correctly enrolled, the green LED will flash
and the buzzer will buzz one time.
IMPORTANT:
If the enrolment procedure is interrupted by an unsuccessful
identification or a function time out, the whole procedure
needs to be repeated. When a user is enrolling a fingerprint,
the pause between each press of the finger should be at least
two seconds. Sometimes, more than three presses will be re-
quired to successfully enrol a user.

7. DELETING A USER FINGER

Inokey provides a »delete user finger« function without em-
ploying a visual database (e.g. a fingerprint template can not
be connected to the user's name, surname or other vital data).
This means that the user who has to be deleted must be pres-
ent, but also that the user's identity cannot be revealed to a
third party. User finger delete selection is done via a positive
match of swiped finger. Only one finger of a user can be de-
leted at one time, not all fingers of the user at the same time!
If same finger was enrolled more than one time, procedure
must be repeated with the same finger as many times as it
was enrolled. Please check Administrators and users list to
check how many fingers of the user, which should be deleted,
are enrolled and how many times same finger was enrolled.
How to delete a user?
•
Check the Administrators and users list to see which fingers
of the user, which should be deleted, are enrolled and inform
user which fingers he/she must press.
•
The right button on the Inokey unit should be pressed for 5
seconds whereupon the blue LED will start flashing.
•
An administrator presses his/her finger on the sensor once.
When he/she is identified, the green LED will flash and the
buzzer will buzz one time.
•
The red and green LEDs will flash alternately. Then the user
presses his/her finger on the sensor once. When the user is
identified, the red and green LEDs flash and the buzzer will
buzz three times. The user finger has been successfully delet-
ed from the system.
8. DELETE ALL (USERS AND ADMINISTRATORS)
By performing this function all existing templates in the data-
base are deleted. After this procedure the device database will
be empty and the next three fingerprints enrolled will have
administrator rights again.
This function is used when the Inokey or the place where it is
installed should get a new owner or when there is a need to
change the administrator.
To prevent that delete all function will be performed by mis-
take, 2 authentications by administrator are required.
How to delete all?
•
Press the left and right button together for a period of 10 sec-
onds whereupon the blue and red LEDs will flash alternately.
•
The administrator then presses his/her finger once. Identifi-
cation is confirmed when the green LED flashes and the buzz-
er buzzes one time.
•
The blue and red LEDs will flash alternately again. The admin-
istrator then presses his/her finger once again. Identification
is confirmed when the green LED flashes and the buzzer buzz-
es at the same time.
•
The red and blue LEDs will flash and the buzzer will buzz five
times simultaneously. All fingerprint templates will then have
been deleted.
IMPORTANT:
When performing the 'Delete all' function it is necessary
that the administrator confirms it twice. At any time during
the execution of the 'Delete all' function, the function can be
stopped with time out.

FACTORY RESET

How to delete all if administrator is not available anymore?
There is a black pushbutton on the internal unit, which is lo-
cated inside the door, beside the motor lock. The lock must
be dismounted to access the button. Press the button for 30
s and after this time fingerprint data base is deleted. After
performing the factory reset, all fingerprints in the database
are erased.
5