Setup Instructions; Preventative Maintenance - K Tool International KTI63134 Guide Du Propriétaire

SETUP INSTRUCTIONS

This is the safety alert symbol used for the SETUP INSTRUCTIONS section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury or death.
Refer to parts breakdown on page 5:
1. Attach saddle angles (#2) to saddle (#1) using screws (#7), flat washers (#8) and nuts (#9) for each saddle angle.
2. Attach fingers (#3) to saddle angles using bolts (#4), flat washers (#5) and nuts (#6) for each finger.
3. To assemble chain, attach hook standoff (#11) to finger and secure washer (#5) and nut (#6). Insert ad j ust m ent hook (#12) through
the hook standoff and secure by using a washer (#5) and wing nut (#10). Attach one end of chain to adjustment hook (#12) and
secure remaining end of chain (#13) by at t ach i ng to finger and se c ur i ng with bolt (#4), flat washer (#5) and nut (#6).
4. To attach adapter to service jack, first remove service jack saddle and raise jack to maximum height. Be sure angle adjustment is
facing down w ard. Insert adapter into service jack saddle assembly and secure by using screw (#26), washers (#25) and washer
(#24).
OPERATING INSTRUCTIONS
This is the safety alert symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential
personal injury hazards. Obey all instructions to avoid possible injury or death.
1. Lift the vehicle to the desired work height, and support the vehicle in accordance with the lift manufacturer's recommended lifting
and support procedures.
2. Position the jack directly under the transmission. Pump the handle, and the adapter will start to rise. Raise the adapter to a height
very close to the center of balance point of the transmission, but do not touch the transmission.
3. Loosen the bolts that secure the saddle angles to the saddle and the bolts that secure the fingers to the saddle angles. The
saddle angles and fingers can be adjusted in and out to help position the transmission on the saddle. Now gently raise the
adapter so it supports the transmission. Make a final adjustment of the angles and fingers and tighten all hardware. Fore and aft
saddle tilt adjustment may be necessary to properly fit the angle of the transmission on the adapter.
4. The chain should be pulled over the center of balance portion of the transmission and secured on the chain hook. Rotate the wing
nut to take up the slack in the chain and secure the transmission to the saddle.
5. Remove the transmission from the engine according to instructions in the vehicle service manual.
6. Once the transmission has been disconnected from the engine, very slowly turn the jack's release knob in a counterclockwise
direction to make sure the jack's saddle and transmission do not hang up on any under vehicle components, wiring, fuel lines,
etc. Continue to lower the jack all the way down.
7. Remember to secure the transmission to the adapter before installing, and follow the vehicle manufacturer's installation
instructions.

PREVENTATIVE MAINTENANCE

This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to
potential personal injury hazards. Obey all instructions to avoid possible injury or death.
1. Always store the adapter in a well protected area where it will not be exposed to inclement weather, corrosive vapors, abrasive
dust, or any other harmful elements. The adapter must be cleaned of water, snow, sand, grit, oil, grease or other foreign matter
before using.
2. The adapter must be lubricated periodically in order to prevent premature wearing of parts. A general purpose grease must be
applied to fore and aft tilt screw and tilt pivot pins.
3. Every adapter owner is responsible for keeping the adapter labels clean and readable. Use a mild soap solution to wash external
surfaces of the adapter. Contact K-Tool International for a replacement label if your adapter's label is unreadable.
4. Inspect the adapter before each use. Do not use the adapter if any component is cracked, broken, bent or shows sign of damage.
Do not use the adapter if it has loose or missing hardware or components, or is modified in any way. Take corrective action before
using the adapter again.
KTI63134 3 7/2/14