Publicité
Les langues disponibles
Les langues disponibles
InSTALLATIOn AnD CARE InSTRUCTIOnS
Plumbing equipment DREAM Light RGB 12/10/8 LED
Water line: arrange your shower box with the water supply line and coupling for the showerhead. The coupling
must be above the ceiling. (Fig. 1). 20 litres of water per minute is enough for the Dream showerhead to work. In fact,
the showerhead, which is installed parallel to the floor, supplies a "free falling" stream of water like soft rain. Make
sure that the faucet supplies at least 25 litres of water per minute. Naturally, the higher the flow rate of the faucet, the
better the showerhead will work.
Also make sure that the hot water heater supplies enough hot water for proper functioning.
GB
Plumbing equipment DREAM Light RGB 4 LED
16 litres of water per minute is enough for the Dream showerhead to work. Make sure that the faucet supplies at least
20 litres of water per minute.
Electrical equipment
Power connection: arrange your shower box with the electrical connection for the showerhead LED lights,
•
placing it above the false ceiling (Fig. 1). Warning: The electrician must use a power cable thatis two-pole,
!
1 mm2 size, outside diameter between 5 and 13 mm.
•
The transformer 7V ~ / 230V ~ – 50/60 Hz including filter, must be installed outside the shower box in a safe
place away from areas 1 and 2 as indicated in the CEI 64-8/7 (Fig. 1) standard.
Control keypad
Fix a 3 module recessed box to the wall. The box may be positioned either inside or outside your shower
box. Fit this with a corrugated tube 20mm in diameter to connect the recessed box to the upper part of
the false ceiling (Fig. 2).
Warning: the keypad is supplied with a connecting cable that is 3 m long. If the keypad is positioned in such a way
that the cable does not reach the electronics board, you will need to ask for an extension cable.
False ceiling
•
Once the electrical and hydraulic systems are hooked up, realise the false ceiling with suitable reinforcement,
as when mounting a chandelier, and make sure it is perfectly level.
•
Keep a distance of at least 12 cm between the ceiling and the false ceiling (Fig.1). Position the template, mark
with a pencil the 6 attachment holes and the central beak-through that will house the electrical and hydraulic
parts of the showerhead (Fig.2).
•
Make the 6 attachment holes having a 10 mm diameter
•
Make the beak-through (Fig.3)
•
Insert the 6 expansion screws and make sure that they are placed accurately (Fig.4).
Showerhead installation
•
Insert the quick disconnect coupling (4), complete with flow switch (5) to the showerhead, and block the Allen
screws using their wrench (15), (Fig.5).
•
Open the bipolar terminal box IP68 (7) and attach the electrical connections that go to the transformer
(Fig.6).
•
Connect the bipolar connector sockets (6) (Fig.7).
•
plug the mains cable of the keyboard into the socket provided and connect the cable terminal to the 4-pole
connector (17) (Fig. 8).
•
Connect one end of the hose (10) to the flow switch (5) and the other end to the water supply line on the wall
(Fig.9). If there is a ½"F wall connection, use the adaptor (14) ½"M × ½"M that is included.
•
Lay the showerhead in correspondence of the 6 expansion screws that were previously inserted
in the false ceiling, and tighten the 6 screws (12) included (Fig.10) until the showerhead is properly fitted to
the false ceiling (Fig.12). Make sure that the screws are fully tightened, about 16 full turns every screw (Fig.11).
Electrical equipment - Technical specifications
1. Electric connection...............................................................................
Absorbed electricity 0,1A class of protection II
2. Electric cable......................................................................................... bipolar, 1 mm² size, outside diameter
3. Dream Rectangular lights 500×400 mm......................................... 12 low voltage LEDs
Dream Rectangular lights 400×300 mm
4. Dream Cube lights 400×400 mm...................................................... 10 low voltage LEDs
Dream Cube lights 300×300 mm
5. Dream OKI lights, 400 mm dia. ......................................................... 8 low voltage LEDs
Dream OKI lights, 300 mm dia. ........................................................ 4 low voltage LEDs
6. Safety Transformer.............................................................................. 7V ~/ 230V~ – 50/60 Hz to be installed
outside the
according to prescription CEI 64/8)
7. Grade of protection ..............................................................................
8. Electronics board...................................................................................IP66/IP67
12
220/230V ~ – 50/60 Hz - max 20w
5 mm to 13 mm (supplied by customer)
4 low voltage LEDs
4 low voltage LEDs
safety area (in compliance with standard DIN VDE 0100, part 107 –
IP x 5 (excluding transformer)
DREAM
& DREAM
LIGHT RGB
9. Control keypad.......................................................................................IP65
10. Safety mark............................................................................................ CE
The electrical systems must be carried out by a qualified technician in accordance with the national and international
laws in force.
How the CHROMOTHERAPY system works
Bossini's CHROMOTHERAPY system can be set to come on automatically when water begins to flow through the
shower head or controlled manually using a control keypad.
•
If set to automatic, as soon as the water begins to flow, the chromotherapy cycle will be activated
automatically. It will switch off automatically when the flow of water to the shower head stops.
•
If set to manual control, it is possible to start a chromotherapy cycle even if no water is passing through the
shower head. You can also use the keypad to lock the chromotherapy cycle on any one of the eight colours. The
lock will remain active until the system is switched off.
When set to manual, the keypad controls the chromotherapy system as follows:
-
press once to activate the cycle by changing the colour
-
press a second time to lock the colour being displayed
-
press a third time to switch the system off
The Bossini system also allows you to use the keypad 'in a combination mode. For example, you could set the cycle
to come on automatically with the flow of water and then lock a colour using the keypad. Using the keypad would
disable the automatic mode, and you would need to use the keypad from then on to control the system.
•
The Time-Out function ensures that the appliance switches itself off after around 30 minutes of no keypad
activity when in manual mode.
RECOMMENDATIONS FOR PROPER USE
Proper use of this product will allow you to avoid damages to the bathroom environment.
*
To prevent impurities or debris from getting inside the product and causing functional problems,
always flush out the system before connecting it to the supply pipes.
It is recommended to install the filter at the system's water intake.
*
To keep the diffuser clean and prevent lime scales from clogging the diffuser, we advise that you
periodically rub the silicone nozzles to free them of the lime deposits.
CLEANING
Dear Customer,
Congratulations for choosing a Bossini product and we thank you for the trust you have given us. To keep the material's
appearance as long as possible, a few guidelines must be followed.
Cleaning metal parts: water contains calcium that deposits on surfaces and forms unpleasant spots. For routine
cleaning, simply use a damp cloth with a little soap, rinse and dry. Calcium spots can therefore be avoided by drying
after use.
Important note: Using only a soap-based detergent is recommended. Never use abrasive detergents or disinfectants
or those containing alcohol, hydrochloric acid or phosphoric acid, Bleach, chlorine etc
Cleaning the rubber nozzles: the showerhead is equipped with the "Easy-Clean" system with silicon nozzles. Calcium
is a shower's worst enemy and that is why Bossini proposes theEasy-Clean" system. These silicon nozzles are extremely
heat resistant and with hot water they dilate, thus detaching the first layer of calcium. Moreover, periodically rubbing
the silicon nozzles manually easily gets rid of calcium. With one simple gesture, your shower is always perfect.
Dear Customer, we would like to remind you that the warranty on our product's surface is not valid if the material
undergoes treatment different than that suggested. The warranty does not cover any damage due to deposits of
calcium or impurities.
WARRANTY TERMS
We congratulate you and thank you for choosing a Bossini quality product
The product is covered by 2 Years warranty against any defects due to manufacturing faults.
The warranty does not cover damages caused by improper installation or use, neglect, incorrect plumbing, normal
fair wear and tear, damages caused by limescale deposits or impurities, the use of detergents and maintenance
products other than those specifically recommended in our instructions manual. Furthermore Bossini is not responsible
for labour costs and/or damages, whether accidental or consequent to the installation, repairing or replacement of the
product.
The request for replacement under the terms of this warranty must be made in a letter setting out the date and place of
purchase and giving a brief explanation of the problem. The letter must be received by us within the warranty period
and must be accompanied by proof of the purchase date (e.g. a receipt). The warranty only covers production faults
/ defects and is strictly limited to the repair or free replacement of the parts which are recognised to be defective. The
defective parts have to be returned to Bossini carriage free with a report describing the defect. Bossini reserves the right
to inspect the part alleged to be faulty or defective and to evaluate the applicability of the warranty terms.
The warranty period commences on the date the product is purchased, evidenced by the relevant purchase
document (e.g. receipt, invoice, cash voucher) and it is NOT renewable.
For further information please contact Bossini or its distributor.
FALSE CEILInG SHOwERHEADS
FLAT LIGHT RGB
GB
13
Publicité
