Cleaning And Maintenance - Royal Catering RCCC-160ST Manuel D'utilisation

EN
3. To turn on the backlight, press the „bulb" button [9].
When this button is pressed again, the backlight will
be turned off.
4. Defrosting function:
• o activate the defrost function, press and hold the
button [9] for 6 seconds.
• To deactivate the defrost function, press the button
[9] again.
5. Cooling LED [11]:
• While the device is running (cooling), the LED is on
• When low temperature inside the refrigerator
compartment is constant, the LED is on
• The LED [12] will flash while the device start is
delayed
6. Defrosting LED [12]:
• The LED during defrosting (defrosting) is on
• When defrosting is complete, the LED turns off
• The LED will flash if the defrosting is delayed
• Both LEDs will flash during a Delayed Start, i.e. the
time the machine must wait to restart operation.
7. Defrosting LED [12]:
• Hold the settings button [6] for 6 seconds. The
device will enter the setting adjustment mode.
• The device will display the possible parameters to be
changed: to change a displayed parameter, press the
button [6] when it is displayed and after changing
the value, confirm it with the same button [6]; to go
to the next parameter, press the buttons (arrows) [7]
and [8].
• After 10 seconds of inactivity, the device will exit the
settings menu and return to the normal operating
mode
Dis- Function Setting range Factory
played setting
code
E1 Lower -20 C / -4oF 2 C / 36
o o
temperature
limit
E2 Upper 49 C / 120 F 6 C / 43
o o o
temperature
limit
E3 Temperature 1 – 10 C / 2 – 4oC / 7
o
fluctuation 18 F
o
E4 Delayed start 0 – 10 (minutes) 5
E5 Room -5 – 5 C / -9 -2 C / 4
o o
temperature – 9 F
o
sensor
E6 Cooling 0 C / 0
o
temperature
sensor
F1 Cooling time 1 – 60 (minutes) 25
12
F2 Cooling cycle 0 – 24 (hours)
F3 Cooling end 0 – 20 C / 32
o
temperature – 68 F
o
F4 Displayed 0 - room tem-
temperature perature
1 - cooling
temperature
(at setting „1":
the room tem-
perature will be
displayed after
a defrosting
process is com-
pleted and after
a 20-minute
delayed start)
C1 Temperature 0 – C
o
unit 1 – F
o
8. Restoring factory settings:
• Press button [8] for 2 seconds. The device beeps.
• Then hold the [7] button for 6 seconds. The display
will start flashing.
• Wait 10 seconds. The device will return to the
operating mode in the factory settings.
9. Parameter change lock:
• Hold button [8] for 10 seconds. The message „OFF"
will start flashing on the display, which means that
changing the parameters according to which the
device operates is not possible.
• To unlock this function, press the [8] button again for
10 seconds until the display flashes „ON".
3.3.3. WARNINGS
F
o
1. Do not spray flammable substances in the vicinity of
the device. It is a fire hazard.
2. After a power cut or the device disconnection from
the power supply, always wait at least 5 minutes,
F
o
then plug the device in and restart it.
3. The device is not designed to store medical supplies
or drugs.
4. It is not recommended to keep the device door open
F
o
for a long time or open it too often. It affects the
quality of keeping the cold air inside the device.
5. Do not put hot food into the device. Food must first
be cooled to room temperature.
6. Never touch the compressor, it can cause severe
burns.
F

3.4. CLEANING AND MAINTENANCE

o
a) Always unplug the device before cleaning it.
b) Use only non-corrosive cleaners to clean the surface.
c) Use only mild, food-safe detergents to wash the
F
o device.
d) After cleaning the device, all parts should be dried
completely before using it again.
e) Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
f) Do not spray the device with a water jet or submerge
it in water.
Rev. 23.03.2022
g) Do not allow water to get inside the device through
4
vents in the housing of the device.
h) Clean the vents with a brush and compressed air.
20 C /
o
i) The device must be regularly inspected to check its
68 F
o
technical efficiency and spot any damage.
j) Use a soft, damp cloth for cleaning.
0
k) Do not use sharp and/or metal objects for cleaning
(e.g. a wire brush or a metal spatula) because they
may damage the surface material of the appliance.
l) Do not clean the device with an acidic substance,
agents of medical purposes, thinners, fuel, oils or
other chemical substances because it may damage
the device.
m) Before cleaning the refrigerator compartment, first
remove everything stored inside and disconnect the
device from the power supply. Clean the inside with
a wet cloth, and then wipe everything dry.
DISPOSING OF USED DEVICES
0
Do not dispose of this device in municipal waste systems.
Hand it over to an electric and electrical device recycling
and collection point. Check the symbol on the product,
instruction manual and packaging. The plastics used
to construct the device can be recycled in accordance
with their markings. By choosing to recycle you are
making a significant contribution to the protection of our
environment. Contact local authorities for information on
your local recycling facility.
TROUBLESHOOTING
PROBLEM SOLUTION
- Check that the device is properly
connected to the power supply
No cooling - Check that the fuse is not damaged
- Check if there is electricity in the
socket
- Check if the device has not been
placed in direct sunlight
- Check that there are no other devices
that emit heat in the vicinity of the
device
- Check that the device vents are not
blocked
- Check that the device door is closed
Unsatisfactory - Check that the seals are not
cooling level deformed or damaged
- Check that there is not too much
produce in the cooling compartment.
If so, reduce the amount of produce.
- Check that the food inside the
refrigerator is not blocking the vents
and restricting the circulation of cold
air
- Adjust the temperature controller
- Check that the device is well levelled
- Check that the device is not touching
Noise the wall or another object
- Check that there are no loose objects
inside the device
Rev. 23.03.2022
EN
Please note: The following phenomena should not cause
worry:
1. A sound of flowing water can be heard while the
device is operating. This is normal as the coolant
circulates through the refrigeration system.
2. Condensation may form on the outside of the device
in wet seasons. Wipe the wet areas with a dry cloth.
13