Morphy Richards Redefine Mode D'emploi page 9

Features
1 Start/StopButton
Starts and pauses the heating process. Can also be used
to pause dispense while in progress and put the Hot Water
Dispenser into standby mode.
WaterVolumeDial
2
Controls the volume of water to be heated and
dispensed. Volume is displayed on the LCD screen (15).
3 LCDScreen
Displays volumes, temperatures, functions, and warnings.
4TemperatureButton
Adjusts the temperature of dispensed water, turns sounds on
and off.
DispenseButton
5
Switches the Auto Dispense feature on and off.
6 DispenseNozzles
7 Watertank
Contains the BRITA MAXTRA Cartridge 19, BRITA Memo 20 and
BRITA Hopper 21.
8 Drip T ray
9 Drip T rayCover
0Drip T rayIndicator
1
'Full' icon indicates when the Drip Tray needs to be emptied.
11HeatIcon
Displays when the heat cycle is in process.
12Water T ankIcon
Displays when the tank needs to be refilled.
13DispenseIcon
Displays when water is ready for dispense.
1 4AutoDispenseIcon
Displays when the auto dispense feature is enabled.
1 5DispenseVolumeDisplay
Displays the volume of water to be heated and
dispensed.
1 6DescaleIcon
Displays when the Hot Water Dispenser requires
descaling.
1 7TemperatureIcon
Displays the temperature the water will be heated to prior to
dispense.
1 8StandbyLight
1 9BRITAMAXTRACartridge
 B RITAMEMO
2 0
Monitors the life of the MAXTRA Cartridge.
21BRITAHopper
22WaterLevelSensor
23MainUnit
Using the Hot Water
Dispenser
BeforeusingyourHotWaterDispenser,orifit
hasnotbeenusedforoveraweek,followthese
instructionstoboilthemaximumamountofwater,
thendiscardtoensurethesystemisflushed
through.
The following instructions detail the steps to
follow to use your Hot Water Dispenser. For Installation of
the BRITA Filtration system see 'Installing a BRITA MAXTRA
Cartridge'.
Filtering water through the BRITA Maxtra
Cartridge takes around 4 minutes for 1.5L. Ensure enough
water has been filtered and is ready for use in the water tank
before heating.
If required, follow steps of 1-6 of 'Resetting the system'
3
to reset the system and then discard the water. If the Hot
Water Dispenser is in standby mode, press any button to
wake.
Pull out the Drip Tray (8) from the Main Unit (23)
4
(if needed).
Place the required vessel (cup, pan, pot etc.) under the
5
Dispense Nozzles (6). One or two vessels can be filled
at the same time during each dispense cycle, provided
they are the same size.
Adjust the temperature of the water by pressing the
6
Temperature Button (4) to cycle through the
options (85,95 & 100°C). The water temperature will be
displayed on the screen (17).
Turn the Water Volume Dial (2) to adjust the Dispense
7
Volume (15).Your Hot Water Dispenser can heat between
150ml to 1.5L of water per cycle.
You can automatically dispense volumes of water at
8
600ml and below. To turn this feature on or off, press the
Dispense Button (5). This function cannot be selected for
volumes over 600ml. These must be dispensed manually.
Press the Start / Stop Button (1) to begin heating.Your
9
Hot Water Dispenser will sound and the heat cycle will
begin. Once started, the volume and
temperature can only be changed during the first few
seconds of the heating cycle.
Once ready your Hot Water Dispenser will sound.
1 0
The hot water will be dispensed automatically. If the
manual dispense function has been selected, press the
Dispense Button (5) to begin dispensing.

g

f

d

e

i

q
∂ 
t