Before Using - Bodum 11303 BISTRO Mode D'emploi

the plug. If it still does not fit, contact a qualified electrician.
Do not modify the plug in any way.

BEFORE USING

Clean the blender before using it for the first time. See CARE
THE BLENDER
AND CLEANING section.
HOW TO USE You can store the excess power cord in the cord retainer (9)
YOUR BLENDER
on the bottom of the motor base.
Place the blender jar (3) onto the motor base (4). It must stand
sturdily on the motor base.
Insert the main plug into an grounded electrical outlet.
MIXING Note: While any indication lights are lit up or the blender is in
operation, do not touch blades, do not interfere with blade
movements, do not remove blender jar lid or use any utensils
to distribute the foods. Do not take off the jug from the base
during operation.
The consistency of the mixture is liable to change as ingredi-
ents are added; it may be necessary to increase or decrease
the speed accordingly.
Only process max. 12 to 14 standard ice cubes at a time. Use
a spatula occasionally to stir ONLY WHEN the main blender is
switched off.
Cool hot foods to max. 80°C / 176°F before blending and start
mixing at and gradually increase to higher speed.
When mixing at higher speeds (
foods, stop the blender before removing the lid cap to add
ingredients.
Only process max. ½-inch/1.5cm cubes of food.
When processing meat, make sure there is no bones left
Boiling Liquid or solid frozen foods (except for ice cubes)
should not be placed in the blender jar.
Always let the blender jar cool down which has come directly
from a hot dishwasher before placing ice, frozen foods or very
cold liquids.
Important: To prevent overheating of the motor, switch off
the blender after 2 minutes of continuous operation and wait
, ), with full jar or with hot
7
5 minutes before continuing. After 5 Cycles of operation,
wait 15 minutes before continuing.
Place the ingredients in the blender jar (3). Only fill up to
1.25l/40oz (1.0l/34oz for frothing liquids).
Place the lid (2) onto the blender jar so the spout is covered
(A: CLOSE ( ) should align with spout) and push it down firmly.
Place the lid cap (1) into the opening in the lid. Turn on the
main power switch (10) on the back of the housing. The indi-
cation light lights up. The START-button (7) blinks to indicate
the blender is now in the standby-mode.
Select a speed by turning the speed control (5).
Press the START - button (7) to start the motor. The START - but-
ton remains lit up continuosly while the appliance is in
operation.
In , or speeds, you can remove the lid cap (1) carefully
to add liquids or ice cubes. Make sure the content cannot spill
out before you remove the lid cap. When operating with full
pitcher or hot liquids at high speeds (
before removing the lid cap to add ingredients. If blending hot
foods or liquids, remove the lid cap and operate only on
speed.
Press the STOP-button (8) to stop.
If you prefer to use the pulse-mode for mixing, set the speed
and press the PULSE-button (6) and keep on pressing until you
are finished mixing. The PULSE-button remains lit up while the
appliance is in operation.
Stop and check the consistency of foods after some seconds
and use a spatula to redistribute it.
Make sure the main power switch is switched off before
removing the lid.
When you have finished mixing, switch off the appliance and
disconnect the blender from the mains.
Remove the jar from the motor base (4) to serve. Place the lid
on the blender jar in a manner that the content can be poured
out through the strainer (B: STRAIN( ) should align with
spout) or the opening of the lid (C: OPEN ( ) should align with
spout). Keep the lid cap on the lid.
8
EN
, ), stop the blender