Euromate VisionAir Blue Line Mode D'emploi page 19

These settings are:
- X-Changer ON/OFF.
- Setting of sensitivity.
- Reset X-Changer.
8.2.2.1 X-Changer ON/OFF
See 8.2 for the steps to call up the menu.
The X-Changer can be selected by pressing the
buttons [F] [G]. The X-Changer can be switched ON
and OFF with the ENTER button [D].
To confirm the selection, press the PROGRAM button
[H].
8.2.3.2 Setting the sensitivity
See 8.2 for the steps to call up the menu.
The sensitivity can be selected by pressing the
buttons [F] [G]. Pressing the ENTER button [D] allows
the sensitivity to be set from Low to Extreme with the
buttons [F] [G].
pq
To confirm the selection, press the PROGRAM button
[H].
- Low
- Medium
- High
- Extreme
8.2.3.3 Resetting X-Changer
See 8.2 for the steps to call up the menu.
The X-Changer can be reset by pressing the
buttons [F] [G]. Holding the ENTER button [D]
pressed now for 2 seconds resets the hourmeter.
8.2.4 Setting the PIR
The PIR is a motion detector that detects the presence of persons
in the vicinity of the air cleaner. Two different actions can be
linked to the detection. It is also possible to switch off the motion
detector.
8.2.4.1 PIR ON/OFF
See 8.2 for the steps to call up the menu.
The PIR can be selected by pressing the
[F] [G]. The motion detector can be switched ON and
OFF with the ENTER button [D].
To confirm the selection, press the PROGRAM button
[H].
8.2.4.2 Setting the mode
See 8.2 for the steps to call up the menu.
The mode can be selected by pressing the
[F] [G]. Pressing the ENTER button [D] allows the
mode to be set so that the fan runs when a person is
detected or when no-one is detected with the
buttons [F] [G]. To confirm the selection, press the
PROGRAM button [H].
This value is dependent on the desired function.
8.2.5 Activation/Deactivation of the UV Output (optional)
See 8.2 for the steps to call up the menu. The UV option can be
selected by pressing the
button [D] allows the UV output to be activated or deactivated
buttons [F] [G]. To confirm the selection, press the
with the
pq
PROGRAM button [H]. As standard the UV output is activated. If
this has to be changed, this should be carried out by an
authorised person.
pq
pq
pq
buttons
pq
buttons
pq
pq
buttons [F] [G]. Pressing the ENTER
pq
PLEASE NOTE!
Do not use UV in position 1 and 2 to avoid the production of
ozone.
8.2.6 Activation/Deactivation of the ACC Output
This option is reserved for future use and is therefore not
described in detail here. Changing the setting has no influence on
the function of the VisionAir Blue Line. This setting has to be
carried out by a authorised person.
8.2.7 Setting / Programming the TIMER
Four switching points can be programmed on the Visonair Blue
Line. One switching point can be set per day or per cluster of
days. The clock does not have an automatic summer/winter
changeover so that the time has to be corrected manually.
8.2.7.1 Setting the clock
The clock has its own battery and will therefore
continue to run normally even if the power supply to
the air cleaner is disconnected. Any programmed
switching times are also retained.
See 8.2 for the steps to call up the menu.
The timer can be selected by pressing the
[F] [G]. Confirm the timer selection by pressing the
ENTER button [D]. The clock can now be set by
pressing the ENTER button [D] again. The hours can
be set by pressing the
are entered by pressing the PROGRAM button [H].
The next step is to enter the minutes and that is
performed in the same way. Then the day has to
be entered.
8.2.7.2 Setting switching points
See 8.2 for the steps to call up the menu.
The timer can be selected by pressing the
[F] [G]. Confirm the timer selection by pressing the
ENTER button [D]. A switching point can now be set
by pressing the
Enter button. The hours can be set by pressing the
buttons [F] [G]. The hours are entered by pressing the
PROGRAM button [H]. The next step is to enter the
minutes and that is performed in the same way. Then
the day has to be entered. The last step is to enter the
fan speed followed by the PROGRAM button [H].
When Timer mode is now selected with the
buttons [F] [G], the air cleaner will start and stop at
the entered switching points. The indicator lights
up orange.
8.2.7.3 Deleting a switching point
See 8.2 for the steps to call up the menu.
The timer can be selected by pressing the
[F] [G]. Confirm the timer selection by pressing the
ENTER button [D]. A switching point can now be
selected by first pressing the
followed by the ENTER button [D] and then selecting
with the
pq
point by pressing the PROGRAM button [H].
User Manual VisionAir air cleaner
buttons
pq
buttons [F] [G]. The hours
pq
buttons
pq
buttons [F] [G] followed by the
pq
pq
buttons
pq
buttons [F] [G]
pq
buttons [F] [G]. Delete the switching
pq
19