Sony HDCU2000 Mode D'emploi page 15

AUX REMOTE 8-pin multi-connector (1)
TRUNK A 12-pin (1)
TRUNK LINE D-sub 9-pin, female (1), RS-232C, for CHU
transmission or system expansion
I/O PORT D-sub 15-pin, female (1)
(JAE-made DA-C1-J10 recommended)
LAN 8-pin (1)
NETWORK TRUNK 8-pin (1)
Input connectors
AC IN (1), 100/120/220-240 V
(To change to a different power supply,
contact a Sony service or sales
representative.)
SDI RET IN BNC-type (4)
3G-SDI: SMPTE 424M/425M, 2.970 Gbps/
2.967 Gbps
HD-SDI: SMPTE 292M, 1.485 Gbps/
1.4835 Gbps
SD-SDI: SMPTE 259M, 270 Mbps
VBS RET IN BNC-type (4), analog signal, 1.0 V p-p,
75 ohms
REFERENCE BNC-type (2), loop-through output
HD: SMPTE 274M, tri-level sync, 0.6 Vp-p,
75 ohms
SD: Black burst (NTSC: 0.286 Vp-p,
75 ohms/PAL: 0.3 Vp-p, 75 ohms) or NTSC
10F-BB
PROMPTER 1, 2 BNC-type (4), loop-through output, analog
signal, 1.0 Vp-p, 75 ohms
MIC REMOTE D-sub 15-pin (1) (JAE-made DA-C1-J10
recommended)
HD PROMPTER IN BNC-type (1), SMPTE 292M, 75 ohms,
1.485 Gbps/1.4835 Gbps
Output connectors
AUDIO OUT CH1, XLR 3-pin, male (2), 0 dBu/–20 dBu/+4 dBu
CH2
AES/EBU BNC-type (1), AES/EBU format
CHARACTER BNC-type (1), VBS, 1 Vp-p, 75 ohms,
character on/off switchable
WF REMOTE D-sub 15-pin, female (1) (JAE-made DA-
C1-J10 recommended)
3G/HD SDI OUTPUT BNC-type (2)
3G-SDI: SMPTE 424M/425M, 0.8 Vp-p,
75 ohms, 2.970 Gbps/2.967Gbps
HD-SDI: SMPTE 292M, 0.8 Vp-p, 75 ohms,
1.485 Gbps/1.4835 Gbps
3D-SDI/HD-SDI selectable.
3G/HD SDI OUTPUT BNC-type (2)
(MONI)
3G-SDI: SMPTE 424M/425M, 0.8 Vp-p,
75 ohms, 2.970 Gbps/2.967Gbps
HD-SDI: SMPTE 292M, 0.8 Vp-p, 75 ohms,
1.485 Gbps/1.4835 Gbps
3G-SDI/HD-SDI and character ON/OFF
selectable
HD/SD SDI OUTPUT BNC-type (2)
HD-SDI: SMPTE 292M, 0.8 Vp-p, 75 ohms,
1.485 Gbps/1.4835 Gbps
SD-SDI: SMPTE 259M, 0.8 Vp-p, 75 ohms,
270 Mbps
HD-SDI/SD-SDI selectable.
HD/SD SDI OUTPUT BNC-type (2)
(MONI)
HD-SDI: SMPTE 292M, 0.8 Vp-p, 75 ohms,
1.485 Gbps/1.4835 Gbps
SD-SDI: SMPTE 259M, 0.8 Vp-p, 75 ohms,
270 Mbps
HD-SDI/SD-SDI and character ON/OFF
selectable
SYNC BNC-type (1)
HD: BTA-S001, tri-level sync, 0.6 Vp-p,
75 ohms
SD: composite sync, 0.3 Vp-p, 75 ohms
HD SYNC/SD SYNC selectable
HD TRUNK OUT BNC-type (1)
SMPTE 292M, 0.8 Vp-p, 75 ohms,
1.485 Gbps/1.4835 Gbps (Available only
when camera single link format is selected.)
Supplied accessories
Number plates (1 set)
Fuses (1 set)
Operation guide (1)
Operation manual (CD-ROM) (1)
Optional accessories
AC power cord:
USA and Canada: 1-551-812-XX
Other countries: 1-782-929-XX
Power cord plug holder
USA and Canada: 2-990-242-01
Other countries: 3-613-640-01
HKCU2007 3G/HD SDI Output Expansion Unit
HKCU1001 SD Encoder Unit
HKCU1003 Multi Interface Unit
CCA-5-3 Connection Cable (3 meters/10 feet)
CCA-5-10 Connection Cable (10 meters/33 feet)
Expansion Board
Maintenance manual
For the customers in the U.S.A., Canada, Europe,
Australia, and New Zealand
Connectors for optical/electric composite cables:
• LEMO PUW.3K.93C.TLCC96 (to the "CAMERA"
®
connector on CCU)
• LEMO FUW.3K.93C.TLMC96 (to the "CCU" connector on
®
CAMERA)
Caution on the optical/electric composite cable:
For connection between the camera control unit and a
camera, be sure to use an optical/electric signal composite
cable with the connectors specified in this manual in order to
comply with the limit for EMC regulations.
15
Specifications