Setting Date, Time And Beeper Functions; Changing Between Body And Object Mode; Directions For Use - Microlife NC 150 Mode D'emploi

 Ready for measuring AK: When the unit is ready for measuring,
the «°C» or «°F» icon will keep flashing while the mode icon
(body or object) will be displayed.
 Measurement complete AL: The reading will be shown on the
display 3 with the «°C» or «°F» icon and the mode icon
steady. The unit is ready for the next measurement as soon as
the «°C» or «°F» icon is flashing again.
 Low battery indicator AO: When the unit is turned on, the «»
icon will keep flashing to remind the user to replace the battery.

5. Setting Date, Time and Beeper Functions

Setting the date and time
1. After the new batteries are fitted, the year number flashes in the
display BP. You can set the year by pressing the START button
4. To confirm and then set the month, press the M-button 8.
2. Press the START button 4 to set the month. Press the M-
button 8 to confirm and then set the day.
3. Follow the instructions above to set the day, 12 or 24 hour
mode, hours and minutes.
4. Once you have set the minutes and pressed the M-button 8,
the date and time are set and the time is displayed.

If no button is pressed for 20 seconds, the device automat-
ically switches to ready for measuring AK.

Cancel time setup: Press the ON/OFF button 5 during
time setup. The LCD will show Date/Time icons with «--:--».
After that press the ON/OFF button 5 to start the measure-
ment. If no further action is taken within 20 seconds, the
device will automatically turn off.

Change current date and time: Press and hold the M-
button 8 for approx. 3 seconds until the year number
starts to flash BP. Now you can enter the new values as
described above.
Setting the beeper
1. When the device is switched off, press and hold the ON/OFF
button 5 for 5 seconds to set the beeper BQ.
2. Press the ON/OFF button 5 again to either turn the beeper on
or off. The beeper is activated when the beeper icon BQ is not
crossed-out.

If no button is pressed for 5 seconds, the device automati-
cally switches to ready for measuring AK.
NC 150

6. Changing between Body and Object Mode

For changing from body to object mode, slide the mode switch 6
at the side of the thermometer downwards. For switching back to
body mode, slide the switch up again.

7. Directions for Use

Measuring in body mode
1. Press the ON/OFF button 5. The display 3 is activated to
show all segments for 1 second.
2. When the «°C» or «°F» icon is flashing, a beep sound is heard
and the thermometer is ready for measuring AK.
3. Aim the thermometer at the center of the forehead with a
distance of no more than 5 cm. Please remove any hair,
sweat or dirt from the forehead before measuring to improve the
accuracy of the readings.
4. Press the START button 4 and steadily move the ther-
mometer from the middle of the forehead to the temple area
(about 1 cm above the eyebrow). The activated blue tracking
light will indicate the area being measured. After 3 seconds a
long beep will verify the completion of measurement. If the
temple area hasn't been reached before the long beep is heard,
repeat the measurement as described above, but move the
thermometer a little faster.
5. Read the recorded temperature from the LCD display.
Measuring in object mode
1. Follow steps 1-2 above, then aim the thermometer at the center
of the object you want to measure with a distance of no more
than 5 cm. Press the START button 4. After 3 seconds a long
beep will verify the completion of measurement.
2. Read the recorded temperature from the LCD display.

NOTE:
 Patients and thermometer should stay in similar room
condition for at least 30 minutes.
 Don't take a measurement while or immediately after nursing a
baby.
 Don't use the thermometer in high humidity environments.
 Patients should not drink, eat or exercise before/while taking
the measurement.
 Don't move the measurement device from the measuring area
before hearing the termination beep.
 10 short beeps and a red LCD backlight alerts the patient that
he/she may have a temperature equal to or higher than 37.5 °C.
EN
3