Noise/Vibration Information; Starting Operation - Bosch EasyPrune Notice Originale

14 | English
Charger
Article number
Rated voltage
Charging current
Charging period (battery dis-
charged)
Weight according to EPTA‑Proced-
ure 01:2014
Protection class

Noise/Vibration Information

Measured sound values determined according to
EN 62841-1.
Typically the A‑weighted sound pressure level of the product
is lower than 70 dB(A).
Overall vibrational values a vector sum of three directions)
h
and uncertainty K determined according EN 62841-1: a
2 2
2.5 m/s , K = 1.5 m/s .
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.

Starting Operation

Use only the chargers listed in the technical data. Only
u
these battery chargers are matched to the lithium-ion bat-
tery of your product.
F 016 L94 019 | (04.03.2020)
EU 2 609 120 713
UK 2 609 120 718
AUS 2 609 120 717
JP 2 609 120 715
KO 2 609 120 716
V
A
h
kg
Battery Charging (see figure A)
Note: The battery is supplied partially charged. To ensure
full capacity of the battery, completely charge the battery
before using your tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not cause damage to the battery.
=
h
The Lithium-Ion battery is protected against deep dischar-
ging. When the battery is discharged, the tool stops the
power-assisted cutting and works in manual mode at all cut-
ting diameters.
The battery needs to be recharged when the battery charge-
control indicator (7) briefly flashes red during a cut.
The charge procedure begins as soon as the mains plug of
the battery charger is plugged into the socket outlet and the
charge Micro USB connector (9) is plugged into Micro USB
socket (5) at the handle top.
The Micro USB socket (5) can only be accessed when the
safety lock (6) is locked.
The battery charge-control indicator (7) indicates the char-
ging progress. The indicator slowly flashes green during
charge process. When the battery charge-control indicator
lights up green continuously, the battery is fully charged.
During the charging procedure, the handle of the machine
warms up. This is normal.
Disconnect the battery charger from the mains supply when
charging process ends.
Protect the charger from moisture.
u
Observe the notes for disposal.
Battery charge-control indicator
The battery charge-control indicator (7) indicates the charge
condition of the battery while in operation.
LED
Continuous lighting, green
Flashing light, green
1 600 A00 3RK
1 600 A00 48V
1 600 A00 48U
1 600 A00 48T
1 600 A00 JL5
5.0
1.0
3.5
0.06
/ II
Capacity
≥35 %
5 − 35 %
Bosch Power Tools
5.0
0.5
3.5
0.06
/ II