DeWalt DCS355 Traduction De La Notice D'instructions Originale page 38

EngLIsh
3. Firmly press the base with the sanding sheet attached
against a flat surface and briefly switch the tool on. This
provides for good adhesion between the platen and the
sanding sheet and also helps to prevent premature wear.
4. When the tip of the sanding sheet becomes worn, detach
the sheet from the platen, rotate and reapply.
Attaching Accessories Using the Universal
Adapter (Fig. G)

CAUTION: To avoid injury, do not use any accessory
for an application where the adaptor may fail to hold
the accessory.

CAUTION: Read and follow all manufacturers' safety
warnings for any accessories used with this tool.

CAUTION: To avoid injury, ensure adaptor and accessory
are securely tightened.
Non-D WALT accessories can be attached using the
e
universal adaptor.
1. Place the washer 20 on the tool.
2. Place accessory on to washer.
12
3. Tighten and secure adaptor nut
Attaching the Cut Guide (Fig. H–M)
The depth/cut guide allows you to precisely cut material at a
specified depth and more accurately track a marked cut line.
1. Attach the cut guide block
tabs on the guide into the accessory side mount slots
13
on the main body of the tool.
nOTE: The depth/cut guide can be attached to either side
of the tool.
2. Secure the block to the main body with the supplied
screw 15 and washer 21
wrench 16 .
Depth Guide (Fig. I, J)
This feature allows you to precisely cut material at a
specified depth.
1. Insert the guide arm 7 as shown in Figure I into the front
slot on the guide block 6 .
2. Adjust the length of the guide by pulling out or pushing
inward to achieve the desired cut depth as shown in
Figure J.
3. Secure the guide in place by turning the depth/cut
adjustment knob clockwise. To release the guide turn
14
the depth/cut adjustment knob counterclockwise.
Cut Guide (Fig. K–M)
This feature allows you to more accurately track a marked
cut line.
1. Insert the guide arm as shown in Figure K into the slots
7
on the left and right sides of the guide block
2. Adjust the length of the guide by pulling out or pushing
inward to achieve the desired length as shown in Figure L.
3. Secure the guide in place by turning the depth/cut
adjustment knob 14 clockwise. To release the guide turn
the depth/cut adjustment knob counterclockwise.
36
18 using hex wrench 16
6 by inserting the accessory
. Tighten with the supplied hex
6 .
nOTE: The guide arm can also be placed in the guard assembly
vertically in order to set the height off a cut. Refer to Figure M.
Attaching the Dust Extraction Adaptor
(Fig. Q)
The Dust Extraction Adaptor allows you to connect the tool to
an external dust extractor, either using the AirLock™ system
(DWV9000-XJ), or a standard 35 mm dust extractor fitment.
1. Attach the dust extraction adaptor
tabs 13 in to the accessory side mount slots
nOTE: The dust extraction adaptor can be attached to either
side of the tool.
2. Insert screw 15 and washer
adaptor 17 and tighten with the supplied hex wrench
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
.
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Ensure switch is fully OFF before installing
the battery.
5
Proper Hand Position (Fig. N)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires the tool to be held as shown in
Figure N.
Instructions for Use (Fig. A)
1. Install the battery pack.
2. To turn the tool ON, hold it as shown in Figure N and press
the variable speed trigger
nOTE: The further the trigger switch is depressed the faster
the tool will operate. If in doubt about the proper speed
for your operation, test the performance at low speed and
gradually increase until a comfortable speed is found.
3. To turn the tool OFF, release the variable speed trigger
Lock on/off Button (Fig. O)
The tool can be locked off by fully depressing the lock on/off
button shown in Figure O.
4
For more comfort in extended use applications, the lock
on/off button 4 can lock the trigger trigger
depressed position.
nOTE: The tool will automatically shut off after operating for
five minutes with the lock-on button engaged. To restart the
17 by inserting the
5 .
21 into the dust extraction
16
1 .
1
1 in the
.
.