Using The Appliance - Bertos G6F2BH6 Mode D'emploi

112 |
- Clean the parts with detergent, water and a suitable
utensil, rinse and dry.
- Make sure when reassembling the parts that they are
slotted in correctly.
WARNING
Every time a replacement involving gas input parts is
made, recheck all functions and test for leakage.
HOW TO REPLACE COMPONENTS
USE ONLY ORIGINAL SPARE PARTS SUPPLIED BY THE
MANUFACTURER. The parts must be replaced solely by
authorised personnel!
To replace the following pieces, firstly remove the control
knobs and the control panel (after having loosened the
fixing screws) as well as any other necessary panel.
Cock with safety valve for open flame and hotplate
EN
"Fullplate" burners - (Fig. 2)
Loosen the gas pipe and thermocouple fitting, loosen
the fitting which fixes the cock to the pipe and replace
the piece.
Thermocouple (for open flame or hotplate "Fullplate"
burners)
Loosen the nuts fixing the thermocouple to the valve and
the burner and replace the piece.
Gas oven thermostat (Fig. 3)
Loosen the nuts of the gas ducts and of the thermocouple,
remove the thermostat bulb from the supporting clips
located inside the oven chamber and replace with the
new cock.
Main burner (gas oven - Fig. 3)
Loosen the fixing screw (D) of the main burner and replace
the burner.
Oven thermocouple
Remove the floor, unscrew the nut on the tap and the
burner and replace the thermocouple.
Resistances (electric oven)
Disconnect the appliance from the mains!
The heating element of the FE1 fan oven is located behind
the back panel of the oven chamber. To remove the
resistance, loosen the screws fixing them to the relative
flange, pull the resistances and relative leads forwards.
Disconnect the leads using a screwdriver and fit a new
resistance following the above sequence in reverse order.

USING THE APPLIANCE

Turning a gas-ring burner with pilot on and off (Fig. 2)
Turn knob (21) to the left until the spark position.
Light the pilot burner using a match or other suitable
(SPARE PARTS)
START-UP
MOD.
means. Keep the knob pressed down while repeatedly
Qn
pressing the piezoelectric ignition button until the flame is
V kW:
lit. Then turn the knob to the high or low flame position in
order to light the main burner of the corresponding ring.
To turn off the burner, turn the knob to the right until the
spark position and the main burner will go out. To turn off
the pilot burner turn the knob to the off position
The flame can be adjusted:
to maximum capacity
to minimum capacity
Start-up and shutdown of the fullplate
Push and turn knob (21) to the left until the spark position
and at the same time press the push button marked
Keep the knob pressed down while repeatedly pressing
the piezoelectric ignition button until the flame is lit. Then
turn the knob to the high or low flame position in order to
light the main burner of the corresponding ring. To turn
off the burner, turn the knob to the right until the spark
position and the main burner will go out. To turn off the
pilot burner turn the knob to the off position
Turn-on and turn-off of gas oven without pilot flame –
(FG1 Oven) (Fig. 3)
Turn-on: open the oven door, press and turn the knob to
position 7 and, while keeping it pressed, use a flame to
turnon the oven at position M. Keep the knob pressed
down for about 20" after ignition, so that the safety device
activates. Now adjust the thermostat setting to the one
most suitable for the chosen cooking method.
Turn-on and turn-off of gas oven with pilot flame – (FG
Oven and Tuttoforno T) (Fig. 5)
To turn on: open the oven door, press and turn the knob to
position or use a piezoelectric lighter, holding it down,
light the pilot flame with a match.
This operation may be observed through the hole in the
oven floor. Keep the knob pressed down for about 20"
after ignition, so that the safety device activates.
Then adjust the thermostatic setting according to the
MOD. N°:
cooking programme required, taking into account that
Qn
V kW: Hz: 50/60 IPX2
the temperatures in relation to the knob positions are
as follows:
Ovens FG1 Position
Ovens FG
Ovens T
MOD. N°:
Qn
V kW: Hz: 50/60 IPX2
MOD. N°:
Qn
N°:
Hz: 50/60 IPX2
(large flame)
(small flame)
MOD. N°:
Qn
V kW: Hz: 50/60 IPX2
.
MOD. N°:
Qn
V kW: Hz: 50/60 IPX2
Degrees °C
160
2 170
3 185
4 200
5 215
6 235
7 260
300
.
.