Transport; Shutdown; Maintenance And Care - Windsor RRB 360 T Guide De L'opérateur

 Empty waste container.
 Push in the waste container and lock it.
 Empty opposite waste container.
Turn off the appliance
Note: After switching off the appliance, the
dust filter is automatically cleaned. Wait for
approx. 2 minutes before opening the appli-
ance cover.
 Set programme switch to step 1 (driv-
ing). The side brush and roller brush are
raised.
 Turn main key to "0" and remove it.
Note
The appliance has an automatic switch-off
function to protect the batteries from dis-
charging. If the appliance is not in use (with
the key switch turned on) for longer than 30
minutes, it will switch off automatically.

Transport

DANGER
Risk of injury and damage! Observe the
weight of the appliance when you transport
it.
 Turn main key to "0" and remove it.
 Secure the wheels of the machine with
wheel chocks.
 Secure the machine with tensioning
straps or cables.
 When transporting in vehicles, secure
the appliance according to the guide-
lines from slipping and tipping over.
Note
Observe markings for fixing points on base
frame (chain symbols). When loading or
unloading the machine, it may only be op-
erated on gradients of max. 12%.
Storage
DANGER
Risk of injury and damage! Note the weight
of the appliance in case of storage.

Shutdown

If the sweeper is going to be out of service
for a longer time period, observe the follow-
ing points:
 Park the sweeper on an even surface.
 Set programme switch to step 1 (driv-
ing). The roller brush and side brushes
are raised to prevent the bristles being
damaged.
 Turn main key to "0" and remove it.
 Lock the sweeper to ensure that it does
not roll off.
 Clean the inside and outside of the
sweeper.
 Park the machine in a safe and dry
place.
 Disconnect battery.
 Charge battery and recharge it approx.
every 2 months.

Maintenance and care

General notes
 First switch off the appliance and re-
move the key before performing any
cleaning or maintenance tasks on the
appliance, replacing parts or switching
over to another function.
 Pull out the battery plug or clamp the
battery while working on the electrical
unit.
Maintenance work may only be carried
–
out by approved customer service out-
lets or experts in this field who are famil-
iar with the respective safety
regulations.
Mobile appliances used for commercial
–
purposes are subject to safety inspec-
tions according to EN 62638 (European
regulation).
Use only roller brushes/ side-brushes
–
that are provided with the appliance or
specified in the Operations Manual.
The use of other roller brushes/ side-
brushes can affect the safety of the ap-
pliance.
Cleaning
CAUTION
Risk of damage! Do not clean the appliance
with a water hose or high-pressure water
jet (danger of short circuits or other dam-
age).
Do not use aggressive and abrasive clean-
ing agents.
Cleaning the inside of the machine
Danger
Risk of injury! Wear dust mask and protec-
tive goggles.
 Open the device hood.
10
-
US
 Blow through machine with com-
pressed air.
 Clean the machine with a damp cloth
which has been soaked in mild deter-
gent.
 Close cover.
External cleaning of the appliance
 Clean the machine with a damp cloth
which has been soaked in mild deter-
gent.
Maintenance intervals
Observe the inspection checklist!
Note: The elapsed-time counter shows the
timing of the maintenance intervals.
Maintenance by the customer
Note: Where maintenance is carried out by
the customer, all service and maintenance
work must be undertaken by a qualified
specialist. If required, a specialised Wind-
sor dealer may be contacted at any time.
Daily maintenance:
 Check the sweeping roller and the side
brush for wear and wrapped belts.
 Check tyre pressure.
 Check function of all operator control el-
ements.
Weekly maintenance:
 Check fluid level of battery.
 Check moving parts for freedom of
movement.
 Check the gasket in the sweeping area
for position and wear.
 Check dust filter and clean filter box, if
required.
 Check function of seat contact switch.
Maintenance to be carried out every 100
operating hours:
 Check battery acid level.
 Check tension, wear and function of
drive belts (V-belt and circular belt).
Maintenance following wear:
 Replace sealing strips.
 Replace roller brush.
 Replace side brush.
Note: For description, see section on Main-
tenance work.
Maintenance by Customer Service
Note: In order to safeguard warranty
claims, all service and maintenance work
during the warranty period must be carried
out by the authorised Windsor Customer
Service in accordance with the mainte-
nance booklet.
Maintenance to be carried out after 5 op-
erating hours:
 Carry out initial inspection.
Maintenance to be carried out every 50
operating hours
 Have maintenance tasks performed ac-
cording to the inspection check list.
Maintenance to be carried out every 100
operating hours
 Have maintenance tasks performed ac-
cording to the inspection check list.
11