Operating Instructions; Delay Start - Kenmore 587.1522 Guide D'utilisation Et D'entretien

Operating Instructions

Option Selections (available on select models)
Wash Cycle Selections
Cycle times are approximate and will
vary with options selected. Hot water is
necessary to activate dishwasher detergent
and melt fatty food soils. An automatic
sensor will check the incoming water
temperature and, if it is not hot enough,
the cycle will be lengthened for automatic
water heating in the main wash and fi nal
rinse of all cycles. This happens even
when HI-TEMP WASH option has not
been selected. When HI-TEMP WASH is
selected, an even higher temperature will
be reached to handle heavier soil loads.
Hi-Temp Wash
When HI-TEMP WASH option is selected,
the dishwasher heats water in the main
wash to approximately 140
This increase in water temperature helps
dishwasher detergent remove food grease
and soil from dishes more eff ectively and
aids in drying. HI-TEMP WASH option
can be used with all cycles except RINSE
ONLY. HI-TEMP WASH is automatically
provided when the HEAVY WASH cycle is
selected.
When HI-TEMP WASH option is selected,
the light above the pad will come on and
remain on until end of cycle. To turn off
the HI-TEMP WASH option, press the pad
a second time. The light above the pad
will turn off .

Delay Start

The DELAY START option allows you
to automatically delay starting your
dishwasher from 1-10, 1-24, 2-4-6 or 6-4-2
hours depending on your model.
On models with 1-10 or 1-24 hour delay,
press the DELAY START pad until the
desired delay time shows in the STATUS
window. A light will come on indicating
the delay start hours and will remain on
until cycle start.
On models with 2-4-6 hour delay, press the
pad once for a 2 hour delay, twice for 4
hours and 3 times for 6 hours. A light will
come on indicating the delay start hours
and will remain on until cycle starts.
On models with 6-4-2 hour delay, press the
pad once for a 6 hour delay, twice for 4
hours and three times for 2 hours. A light
will come on indicating the delay start
hours and remain on until cycle starts.
To cancel the DELAY START option and
begin the cycle before the delay period is
over, press the START/CANCEL pad.
Heat Dry
The HEAT DRY option in combination with
rinse aid will enhance drying performance.
The energy required to use the HEAT DRY
option costs pennies per cycle. You may
choose not to select the HEAT DRY option;
however you will have items in your dish
load that will not be completely dry at the
end of the cycle.
0 F (60 0 C).
10
Sanitize Option
To sanitize your dishes and glassware,
select the SANITIZE option. When
selected, the light above the pad will
come on and remain on until end of cycle.
The water temperature in the fi nal rinse will
o
be raised to 156 F (69
available in HEAVY and NORMAL WASH
cycles. Only these sanitization cycles have
been designed to meet NSF requirements.
The cycle time will be extended until the
proper water temperature is reached.
Washing action will continue during the
water heating delay. For best results, the
incoming water temperature should be at
0 0
least 120 F (49 C).
The sanitize criteria may not be satisfi ed
if there is an interruption of the cycle,
power failure or if the incoming water
temperature is below 120
To turn off the SANITIZE option, press
SANITIZE a second time. The light above
the pad will turn off .
To Cancel a cycle
You can cancel a cycle anytime during the
cycle. Press START/CANCEL pad and the
dishwasher will start a 90 second drain. At
the end of the drain, select the next desired
cycle.
This option is
o
C).
0 F (49 0 C).