En Surge Protective Device; Product Description; Target Group; General Safety Information - OBO Bettermann V20-320 Série Mode D'emploi

Installation instructions
EN Surge Protective Device
Item no. Type
5095 366 V20-0-320
5095 171 V20-1-320
5095 173 V20-3-320
5095 261 V20-1+NPE-320
5095 253 V20-3+NPE-320
5095 291 V20-1+FS-320
5095 293 V20-3+FS-320
5095 341 V20-1+NPE+FS-320
5095 343 V20-3+NPE+FS-320
5095 600 C20-0-255
*
Figure
1

Product description

Surge protection device for equipotential bonding
of power supply systems according to VDE 0100-
443 (IEC 60364-4-44). For mounting on hat rails
and use in distributor housings. Arresters (Figure
) can be connected individually and are en-
1
coded on the rear side, in order to avoid incorrect
connection. They possess a thermodynamic cut-
off unit and have an arresting capacity of up to 40
kA (8/20) per pole.
If there is an error, the visual display switches
from grey to red (Figure ).
With snap-on hat rail bracket (Figure
The spark gap C20-0-255 is intended as an ar-
rester between the neutral conductor N and the
protective conductor (PE conductor).
Only V20-..+FS..: With module for remote sig-
nalling through potential-free changeover contact
(Figure ).

Target group

The device may only be mounted and connected
by an electrical technician.

General safety information

• Before working on power cables, ensure that
they are de-energised and secure them against
unintentional switch-on!
• Do not carry out mounting work during a storm!
• Comply with national laws and standards, e.g.
VDE 0100-534 (HD 60364-5-534)!
OBO BETTERMANN GmbH & Co. KG
Product
Single arrester*
Single pole
Three-pole
Single-pole with NPE
Three-pole with NPE
Single-pole with FS
Three-pole with FS
Single-pole with NPE and
FS
Three-pole with NPE and
FS
Single arrester*

Mounting and installation

The device can be installed in any position (e.g.
vertical or horizontal).
Figure
specifies that,
– in the case of single-branch wiring,
– or, in the case of V wiring,
should ideally not exceed 0.5 m, but never ex-
ceed 1.0 m.
For V wiring, use the connection terminal, item
).
2
no. 5012 010.
• Clamp the protection device onto the hat rail,
• Maintain the stripping length and tightening
• Connection according to the circuit diagram
Protection path I
Total
– –
L – PE/N –
L – PE/N 120 kA
L – N, N – PE 60 kA
L – N, N – PE 60 kA
L – PE/N –
L – PE/N 120 kA
L – N, N – PE 60 kA
L – N, N – PE 60 kA
– –
: VDE 0100-534 (HD 60364-5-534)
connection length a + b
length c
Caution! Risk of overloading!
The connection terminal 5012 010 is
approved for a maximum current load ≤ 50
A.
Use a suitable back-up fuse!
ensuring that the lockable hat rail holder is un-
locked (Figure ).
2
torque (Figure ).
(TN-C systems) or (TN-S / TT systems).
V20-...-320
Circuit
EN
I
PE
diagram
– –
–
1
–
3
< 2 μA
1
< 2 μA
3
–
1
–
3
< 2 μA
1
< 2 μA
3
– –
the total
1
the connection
2
7