Audiovox Rampage ACD-24 Manuel De L'utilisateur page 9

pear on the display panel). When a desired track is
reached, press the Scan button again to cancel
the function and play of the selected track will
continue. Track Scan mode will also be cancelled
by activating the Repeat Play
functions.
cn cn cn cn cn
DISC EJECT ( )
Disc play is stopped, the disc is ejected and the unit
will change to radio operation by pressing this button.
If the disc is not removed from the unit and the button
is pressed again, the disc will be re-loaded and
begin playing.
If the disc is not removed from the disc slot within
15 seconds of being ejected, it will automatically be
re-loaded into the unit to prevent it from being
accidentally damaged. Play of the disc can be
resumed by using the CD Mode Selector
CD player function.
co co co co co
TIME/FREQUENCY SELECTOR (T/F)
This unit can display the clock time, radio frequency or
CD player functions on the display panel. Pressing
the Time/Frequency Selector button when the
radio frequency or CD player track indication is
shown will change the display to show the time.
The time display will automatically return to the radio
frequency or CD player function indication after 5
seconds.
cp cp cp cp cp
FM MONO/STEREO SELECTOR (MONO)
During FM radio operation, this button is used to
select mono or stereo reception of the broadcast
signal. Under normal reception conditions, the unit
should be left in the stereo mode, as indicated by
"ST " on the display panel when listening to an FM
stereo signal. If the stereo signal is too weak for
comfortable listening, press the button to switch to
mono reception (the "ST
pear from the display panel). To return to the
stereo reception mode, press the button again so
that the "ST " indication returns.
cq cq cq cq cq
EQUALIZER SELECTOR (P.EQ)
The P.EQ button applies preset sound effects to
the unit's audio output signal. The P.EQ button,
when pressed, will activate one of three operating
modes ("ROCK, CLAS, or POP"). When the P.EQ
function is active, the bass and treble levels cannot
be changed. When the P.EQ function is not ac-
tive, the unit returns to the user-set bass and
treble levels.
bu cl
or Random Play
cr
to choose
" indication will disap-
cr cr cr cr cr
MODE SELECTOR (MODE)
This button is used to select the radio, or the playback
mode for the CD player or remote CD changer (if
installed). Each press of the button will select a
different mode as indicated on the display panel.
During CD player operation, this button may be used
to change to radio or remote CD changer mode
("CDC") without ejecting the disc (the
cation will remain on the display panel to show that a
disc is still loaded in the unit). Press the button again to
return to integral CD player mode and resume play of
the disc from the point at which it was stopped.
cs cs cs cs cs ct ct ct ct ct
& DISC SELECT (CD+ & CD-)
These buttons are used to increase or decrease
selection of a desired disc for play in the remote CD
changer. To advance to a higher number disc, press
cs
the "CD+" button . To return to a lower number
disc, press the "CD-" button
disc in play will be shown on the display panel.
cu cu cu cu cu
FRONT PANEL RELEASE BUTTON
This button is used to release the mechanism that
holds the front panel to the chassis. To detach the
front panel, press the button so that the left side of the
panel is released. Grasp the released side and pull it
off of the chassis.
To re-attach the panel, position the right side of the
panel in place first and then press the left side of the
panel until the mechanism locks it into place.
dl dl dl dl dl
THEFT-DETERRENT L.E.D.
The theft-deterrent Light Emitting Diode (L.E.D.) is
located behind the front panel and is accessible when
the front panel is removed. The flashing light serves
as a visual warning to the would-be thief that the unit
has been disabled by removal of the front panel.
dm dm dm dm dm
RESET BUTTON
A "RESET" button is located on the front of the chassis
(front panel must be removed to access the button).
The "RESET" circuitry is provided to protect the
microprocessor circuitry and should only be acti-
vated under the following circumstances as it will
erase the time and pre-set memories:
1. Upon initial installation after all wiring is completed.
2. After the position of the frequency step switch on
the bottom of the chassis has been changed.
3. If there is a malfunction of any of the switches on
the unit, pressing the "RESET" button may clear
the system and return to normal operation.
IN indi-
ct
. The number of the
8 8 8 8 8
128-5780E
9 of 48