Technical Data - S+S Regeltechnik AERASGARD RTM - CO2 Notice D'instruction

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

G
®
AERASGARD
RTM - CO
The maintenance-free, microprocessor-controlled AERASGARD
to detect the CO
content in air within a range of 0 ppm to 2000 ppm CO
2
actual temperature is also measured at the same time. The measurement signals
are converted to standard signals of 0 - 10 V. Optionally, this CO
ducer can be supplied with switching output. Elegant enclosure made of plastic, with
snap-on lid, base with 4-hole attachment for installation on vertically or horizontally
installed in-wall flush boxes, with predetermined breaking point for on-wall cable
entry, or in enclosures made of stainless steel (top and bottom part are of stainless
steel, the lid is screwed on), vandalism-secure version e.g. for schools, military
barracks, and public buildings.
The CO
content of the air is determined by an optical NDIR sensor (non-dispersive
2
infra-red technology). The detection range of this CO
ard applications such as monitoring of residential rooms or conference rooms. Room
ventilation on an as-needed basis, improvement of well-being and customer benefit,
increased comfort as well as a reduction of operating costs by energy conservation
are just some of the benefits of employing AERASGARD

TECHNICAL DATA

Power supply:
CARBON DIOXIDE (CO
)
2
Sensor, CO
:
2
Measuring range, CO
:
2
Output, CO
:
2
Measuring accuracy, CO
:
2
Pressure dependence:
Long-term stability:
Gas exchange:
TEMPERATURE
Measuring range,
temperature:
Output, temperature:
Deviation, temperature:
Warm-up time:
Ambient temperature:
Response time:
Electrical connection:
Enclosure:
Dimensions:
Installation:
Protection class:
Protection type:
Standards:
2
®
sensor is calibrated for stand-
2
®
CO
sensors
2
24 V AC ⁄ DC
optical NDIR sensor
(non-dispersive infra-red technology)
dual-beam measuring system
with automatic calibration
0...2000 ppm
at the RTM - CO
- 2S the operating
2
modecan be changed via pushbutton:
Automatic, Manual (Step 1 and Step 2), and OFF
0 -10 V
± 70 ppm plus 5 % of measured value
± 1.6 % ⁄ kPa (referred to standard pressure)
± 1 % of final value per year
by diffusion
0...+50 °C (RTM - CO
⁄ RTM - CO
2
+5...+40 °C (RTM - CO
- 2S)
2
0 -10 V
± 0.2 K at +25 °C
approx. 1 hour
0 ...+50 °C
approx. 1 minute
2
0.14 - 1.5 mm
, via screw terminals
plastic, material ABS,
colour pure white (similar to RAL 9010), stainless steel enclosure optional
98 x 98 x 33 mm (Baldur 2)
100 x 100 x 25 mm (stainless steel enclosure)
wall mounting or on in-wall flush box, Ø 55 mm,
base with 4-hole for mounting on vertically or horizontally
installed in-wall flush boxes for cable entry from the back,
with predetermined breaking point for on-wall cable entry
from top ⁄ bottom in case of plain on-wall installation
III (according to EN 60 730)
IP 30 (according to EN 60 529)
CE conformity, electromagnetic compatibility according to EN 61 326,
EMC directive 2014 ⁄ 30 ⁄ EU, low-voltage directive 2014 ⁄ 35 ⁄ EU
RTM - CO
is used
2
Connecting diagram
. The
2
measuring trans-
2
Connecting diagram
1
2
3
4
5
6
7
8
9
10
11
12
- A)
2
UB+ 24V AC/DC
1
2
UB- 24V AC/DC
3
Free
4
Free
5
GND
6
Free
7
Free
Output CO
content in ppm 0-10V
8
2
Output temperature in °C 0-10V
9
UB+ 24V AC/DC
UB- GND
Free
Free
GND
Output 0-10 V temperature in °C
GND
Output 0-10 V CO
content in ppm
2
Step 2 (normally open contact) 5A/250V~
Step 2 (normally open contact) 5A/250V~
Step 1 (normally open contact) 5A/250V~
Step 1 (normally open contact) 5A/250V~
Rev. 2017 - V21 GB
RTM - CO
2
RTM - CO
- A
2
RTM - CO
- 2S
2

Publicité

Table des Matières
loading

Table des Matières