Switching The Kettle Off; Boiling Water - Inventum HW508 Mode D'emploi

to the product or other things are not covered by the
warranty.
2 | bEFoRE FIRST USE
before you use the appliance for the first time, please do
as follows: carefully unpack the appliance and remove
all the packaging material. keep the material (plastic
bags and cardboard) out of reach of children. check the
appliance after unpacking for any damage, possible from
transportation. Place the appliance on a stable and heat
resistant surface.
the minimum amount of water must be 0.2 liters. the
maximum capacity is 0.8 liters.
before use you must fill the waterkettle to the maximum
level and boil this amount. Do this twice. throw away
the boiled water and rinse the kettle with cold water. the
appliance is now ready to use. the kettle is only suitable
for boiling water. Never fill the kettle with milk, tea, coffee
or others drinks.
3 | boILING WATER
before plugging into a socket, check that the voltage in
your home corresponds with the voltage printed on the
bottom of the appliance. Put the appliance on a cool, flat
and stable surface. connect the appliance to an earthed
socket. You can adjust the length of the cord by pulling it
out from, or pushing it into, the interior of the appliance.
1. open the lid by pushing the button on the lid.
2. Fill the kettle with an amount of water and close the lid
by pushing it down and press the button on the lid.
3. Place the kettle on the base and make sure that the plug
is in the socket.
4. switch the kettle on by pressing the on/off switch down
to position 1.
the pilot lamp will light up.
water.
5. the kettle will automatically switch off when the water
is boiled.
the pilot lamp will switch off.
Attention: never switch the kettle on without water.
if, for whatever reason, the kettle is switched on without
water, the dry-boilprotection will automatically switch
the kettle off. Put the switch back up. in this case take
the kettle from the base and let it cool down for several
minutes. after that, refill the kettle and switch it on again.
Make sure that the lid is closed properly, if not the kettle
will go on boiling and will not automatically switch off.
the kettle will now boil the
4 | SWITCHING THE kETTLE oFF
the kettle will automatically switch off when the water is
boiled and the pilot lamp will switch off. if you want to boil
the water again, you must wait approx. 30 seconds before
you switch it on again, so that the switch can cool down.
the kettle can also be switched off at any time with the
switch. when you take the waterkettle off the base while
boiling, it will switch off. when you place the waterkettle
back on the base, you must again wait approx. 30 seconds
to let the switch cool down before you can switch it back
on.
Attention! it may occur that you see condensation on the
base. this is completely normal and has no consequences
for the use of the waterkettle.
5 | DESCALING
scale can form on the inside of the waterkettle. we advise
to descale the waterkettle from time to time. use a suitable
descalingproduct for waterkettles/ coffeemachines and
follow the instructions.
You can also descale the waterkettle with lemonjuice.
the acid in this juice will remove the scale. this natural
method avoids the use of chemicals. Fill the waterkettle
half-full with warm water. add the juice of half a lemon.
boil the water and leave it to cool for half an hour. throw
away the boiled water and rinse the waterkettle to remove
any remainders. Fill the waterkettle with fresh water and
boil it again. throw away the water and rinse the kettle
once more. Never clean the appliance with detergents.
these products can damage your waterkettle.
6 | CLEANING EN mAINTENANCE
clean the waterkettle on regular bases for continues
performance. Never immerse the waterkettle, the base or
the plug in water or others liquids. let the waterkettle cool
off and always unplug the appliance before cleaning. wipe
the outside of the waterkettle with a damp cloth and dry
the kettle afterwards. Never use any abrasives!
7