Before First Use; Boiling Water; Switching The Kettle Off; Cleaning & Maintenance - Inventum HW 86 Mode D'emploi

2 | before first use
Before you use the appliance for the first time, please do
as follows: carefully unpack the appliance and remove
all the packaging material. Keep the material (plastic
bags and cardboard) out of reach of children. check the
appliance after unpacking for any damage, possible from
transportation. place the appliance on a stable and heat
resistant surface.
the minimum amount of water must be 0,2 liters. the
maximum amount of water to be used is 1 liters. Before
use you must fill the waterkettle to the maximum level
and boil this amount. do this twice. throw away the
boiled water and rinse the kettle with cold water. the
appliance is now ready to use. the kettle is only suitable
for boiling water. never fill the kettle with milk, tea,
coffee or others drinks.
3 | boiLing water
Open the lid by pushing the button and fill the kettle with
an amount of water and close the lid. place the kettle
on the base and make sure that the plug is in the socket.
Switch the kettle on by pressing the on/ off switch down.
the red pilot lamp will light up. the kettle will now boil
the water.
attention: never switch the kettle on without water.
If, for whatever reason, the kettle is switched on without
water, the dry­boilprotection will automatically switch
the kettle off. put the switch back up. In this case take
the kettle from the base and let it cool down for several
minutes. after that, refill the kettle and switch it on
again. make sure that the lid is closed properly, if not the
kettle will go on boiling and will not automatically switch
off.
4 | switching the kettLe off
the kettle will automatically switch off when the water
is boiled and the pilot lamp will switch off. If you want to
boil the water again, you must wait approx. 30 seconds
before you switch it on again, so that the switch can cool
down. the kettle can also be switched off at any time
with the switch. When you take the waterkettle off the
base while boiling, it will switch off. When you place
the waterkettle back on the base, you must again wait
approx. 30 seconds to let the switch cool down before you
can switch it back on.
attention! It may occur that you see condensation on the
base. this is completely normal and has no consequences
for the use of the waterkettle.
5 | descaLing
Scale can form on the inside of the waterkettle. We
advise to descale the waterkettle from time to time.
use a suitable descalingproduct for waterkettles/
coffeemachines and follow the instructions.
you can also descale the waterkettle with lemonjuice.
the acid in this juice will remove the scale. this natural
method avoids the use of chemicals. fill the waterkettle
half­full with warm water. add the juice of half a lemon.
Boil the water and leave it to cool for half an hour. throw
away the boiled water and rinse the waterkettle to
remove any remainders. fill the waterkettle with fresh
water and boil it again. throw away the water and rinse
the kettle once more. never clean the appliance with
detergents. these products can damage your waterkettle.
to remove the anti­scalefilter for cleaning, take the
waterkettle of the base and let it cool down. do not
remove the anti­scalefilter when the waterkettle is still
warm and/or filled with water. pull the anti­scalefilter
straight up out of the spout and clean it with warm water.
make sure while replacing the filter to place it correctly
in the spout. never place the anti­scalefilter loose in the
waterkettle.
6 | cLeaning & maintenance
clean the waterkettle on regular bases for continues
performance. never immerse the waterkettle, the
base or the plug in water or others liquids. Let the
waterkettle cool off and always unplug the appliance
before cleaning. Wipe the outside of the waterkettle with
a damp cloth and dry the kettle afterwards. never use
any abrasives!
11