FALMEC Down draft 90 Mode D'emploi page 24

USING THE RADIO CONTROL
WARNINGS!:
Place the hood away from sources of electromagnetic
waves (e.g. microwave ovens), which could interfere with
the radio control and with the hood electronics.
The maximum operating distance is 5 metres, that may vary ac-
cording to the presence of electromagnetic interferences.
Radio control operated at 433.92MHz.
The radio control consists of two parts:
- the receiver built into the hood;
- the transmitter shown here in the figure.
DESCRIPTION OF TRANSMITTING
COMMANDS
ACTIVATION PROCEDURE
Before using the radio control, follow the procedure below on the
hood pushbutton panel:
• Press LIGHT ( ) and TIMER (
flashing.
• Release the two keys and press LIGHT (
up.
• Release LIGHT ( ): now the receiver is active.
This procedure is also used to deactivate the receiver.
RADIO CONTROL CODE CHANGE
With only one radio control, go directly to point 2.
With several radio controls in the same room, a new code can be creat-
ed by following the procedure below.
Disconnect the power to the hood before starting the pro-
cedure.
1) - CREATE A NEW CODE
The procedure is to be carried out on the radio control.
• Press LIGHT and TIMER
flashing.
• Press DOWN on the radio control: saving is confirmed by three
brief flashes of the display. The new code cancels and replaces the
previous default code.
Reconnect the hood to the electrical power supply, making
sure that the lights and motor are off.
(OPTIONAL)
UP
Motor switch-on and speed in-
crease from 1 to 4. Speed 4 is only
active for a few minutes.
DOWN
Speed decrease and motor
switch-off.
Light ON-OFF
TIMER ON: The motor automati-
cally switches off after 15 min.
The function is automatically dis-
abled if the motor is switched off
( key)
Command transmission active
) simultaneously until all LEDs start
) again until all LEDs are lit
simultaneously until the display starts
2) - ASSOCIATING THE RADIO CONTROL WITH THE HOOD
USING
THE TOUCH PUSHBUTTON PANEL
press LIGHT ( ) on the hood pushbutton panel for 2 seconds:
the LED lights up.
press any key on the radio control within 10 seconds.
RESTORING DEFAULT CODE
the procedure is to be carried out if the hood is disposed of, sold or
transferred.
Disconnect the power to the hood before starting the pro-
cedure.
• Press UP and DOWN
more than 5 seconds: reset is confirmed by three brief flashes of the
display.
• Reconnect the hood to the electrical power supply.
• Proceed with associating the hood and the radio control, as described
in
point 2.
MAINTENANCE
Before cleaning or carrying out maintenance operations,
disconnect the equipment by removing the plug or
switching off the main switch.
Do not use detergents containing abrasive, acidic or corrosive
substances or abrasive cloths.
Regular maintenance guarantees proper operation and performance
over time.
Special attention is to be paid to the metal anti-grease filters: fre-
quent cleaning of the filters and their supports ensures that no flam-
mable grease is accumulated.
CLEANING OF EXTERNAL SURFACES
You are advised to clean the external surfaces of the hood at least once
every 15 days to prevent oily substances and grease from sticking to
them. To clean the brushed stainless steel hood, the Manufacturer rec-
ommends using "Magic Steel" wipes.
Alternatively and for all the other types of surfaces, it can be cleaned
using a damp cloth, slightly moistened with mild, liquid detergent or
denatured alcohol.
Complete cleaning by rinsing well and drying with soft cloths.
Do not use too much moisture or water around the push
button control panel and lighting devices in order to pre-
vent humidity from reaching electronic parts.
The glass panels can only be cleaned with specific, non-corrosive or
non-abrasive detergents using a soft cloth.
The Manufacturer declines all responsibility for failure to comply with
these instructions.
CLEANING OF INTERNAL SURFACES
Do not clean electrical parts, or parts related to the motor
inside the hood, with liquids or solvents.
For the internal metal parts, see the previous paragraph.
24
simultaneously on the radio control for