Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
English
3. Plug the charger into any standard 120 Volt 60 Hz
electrical outlet.
4. The LED
3
flashes RED during normal charge and turns
GREEN for 60 seconds when the battery is fully charged.
5. Fast RED blink indicates a bad battery pack. Please
contact your BLACK+DECKER dealer.
Visit www.blackanddecker.com to locate dealers.
Battery discharging
1. The LED
3
is GREEN when discharging.
2. The LED flashes GREEN when the battery charge is low.
3. The LED flashes RED for 10 seconds when the battery is
fully discharged.
4. The LED flashes RED when the rorary brush is jammed
or entangled. Please refer to section 'Removing and
cleaning the rotary brushes' .
5. Once the unit is fully discharged, the LED
RED for 10 seconds every time the handvac or stick vac
ON/OFF switch is pressed and the unit will not turn ON.
6. A charge cycle is required before the unit will turn ON.
Fig. D
17
16
•
While charging, the charger may get warm, this
is perfectly normal and safe. It is safe to leave the
appliance connected to the charger indefinitely. The
charger automatically reduces power consumption
when charging is complete.
WARNING:
at ambient temperatures below 39 °F (4 °C) or above
104 °F (40 °C). Follow all charging instructions and do
not charge the appliance outside of the temperature
range specified in the instructions.
Removing / Installing Hand Vac (Fig. A)
To remove hand vac:
1. Press the hand vacuum release button
2. Lift the hand vacuum
To install hand vac:
3. Insert the hand vacuum
9
as shown in Fig. C, ensuring it clicks firmly into place.
Switching ON and OFF
hand Vac Mode
1. To switch ON, press the ON/OFF power button
2. To switch OFF, press the ON/OFF power button
nOTE: Return the product to the charger immediately
after use so that it will be ready and fully charged for the
4
3
will flash
13
Do not charge the battery
3
.
1
from the stick vacuum chassis
1
into the stick vacuum chassis
next use. Ensure that the product is fully engaged with
the charger plug.
stick Vac Mode
1. To switch ON, press the Stick vacuum ON/OFF button
2. For increased power, press the power boost button
nOTE: Pressing the power boost button more than
once will cycle the power of the rotary brushes from
normal to boosted.
3. To switch OFF, press the Stick vacuum ON/OFF button
nOTE: Return the product to the charger immediately
after use so that it will be ready and fully charged for the
next use. Ensure that the product is fully engaged with
the charger plug.
Hand Vac Accessories (Fig. E)
Your hand vacuum may be supplied with some of the
following accessory:
The brush tool
-
cleaning of upholstered furniture and fabric.
-
The crevice tool
and hard to-reach places.
Fitting
1. Insert the appropriate accessory into the front of the
hand vacuum
2. Make sure the accessory is fully pushed in.
Fig. E
Dry pick up
For everyday spills of dry material.
-
Do not fill the dust bowl
intake chute.
Optimizing the suction force
In order to keep the suction force optimized, the filters must
be cleaned regularly during use.
Emptying and Cleaning
Removing the dust bowl and filter (Fig. F, G)
9
.
WARNING:
should be cleaned regularly.
1. Press the dust bowl release button
bowl
4
2. While holding the dust bowl over a trash can, pull out
2
.
the filter assembly
2
.
3. Rotate filter
it from the pre filter
14
is designed for more effective
15
allows for vacuuming in narrow
1
as show in Figure E.
1
4
beyond the end of the
The filter is reusable and
straight off as shown in Fig. F.
18
to empty the contents.
19
counterclockwise to unlock and remove
20
. Gently remove any debris.
10
.
.
11
.
10
15
14
5
and pull the dust
Publicité
Table des Matières
