Hudora BigWheel Air All Paths 280 Instructions De Montage Et Mode D'emploi page 8

INSTRUCTIONS ON ASSEMBLY AND USE
EN
TUBE, SHEATH AND RIM CHANGES
In the event that there is still air in the tube, you have to let this
out first over the valve. Using two levers – we recommend a tire
lever – try to pry one side of the sheath over the outer edge of the
rim. Continue this process until the entire side of the sheath is
protruding over the wheel rim.
TUBE EXCHANGE
For the change of the tube, pull the tube from the rim on the
leveraged sheath side. Press the valve back through the hole in the
rim base, in order to completely remove the tube. For the insertion
of a new tube, first lead the valve under the sheath through the
hole in the rim base. Then slightly inflate the tube, this makes
the insertion of the remaining part of the tube into the rim easier.
Press the side of the sheath that is protruding over the edge of the
rim back into the rim base. If necessary, the last remaining part of
the sheath edge can be levered into the rim base.
SHEATH AND RIM CHANGES
For the change of the sheath or else the rim, lever the other side of
the sheath in the same way over the other rim edge. You can then
press/turn the rim together with the tube out. In order to attach
a new sheath, press the rim (if needed a new rim) with already
mounted tubing into the sheath, so that the two sides of the sheath
protrude over both of the rim edges. Then first press back one side
of the sheath completely into the rim base and then do the same
on the other side. If necessary, each of the remaining parts of the
sheath edges can be levered into the rim base.
MOUNTING THE WHEEL
First ensure that the ball bearings are fitted in the wheel hub and
the axle guide sleeve is positioned between them. Once this is
ensured, you can insert the wheel into the fork and thereby fix
it with the axle bolt. Use the two Allen screws for this purpose in
order to counteract both screw sides.
BEARINGS
Your kick scooter is equipped with precision ball bearings, which
were filled with grease under high pressure during manufacture.
For this reason, the rollers of the kick scooter only run lightly and
swiftly, while under load. Bearings are maintenancefree, but they
are wear parts. Caution! Worn bearings make conspicuous audible
noises and their function is constrained. In order to maintain
optimal riding pleasure and to ensure lasting safety, you should
replace bearings, as soon as they begin to exhibit signs of being
worn. In the case of full load and daily use we recommend the
replacement of the rollers and bearings twice a year. Bearings are
available as accessories under http://www.hudora.de/.
MAINTENANCE AND STORAGE
Use a dry or damp cloth only to clean the product; do not use special
cleaning agents! Check the product for damage or traces of wear
and tear before and after each use. Do not make any structural
changes. For your own safety, please use original spare parts only.
These can be sourced from HUDORA. If parts become damaged
or if sharp edges or corners should develop, the product may not
be used any more. If in any doubt, please contact our service team
(http://www.hudora.de/). Store the product in a safe place where
it is protected from the elements, cannot be damaged, and cannot
injure anyone.
Replace damaged or worn assembly parts in order to ensure the
safety of your scooter.
DISPOSAL ADVICE
At the end of the product's life, please dispose of it at an appro-
priate collection point provided in your area. Local waste manage-
ment companies will be able to answer your questions on this.
SERVICE
We make every effort to deliver faultless products. If faults do arise
however, we put just as much effort into rectifying them. Therefore,
you can find numerous information on the product, replacement
parts, solutions to problems and lost assembly manuals at http://
www.hudora.de/.
SPARE PARTS AND ORIGINAL
ACCESSORIES AVAILABLE AT:
http://www.hudora.de/
All images are examples of the design.
8/28