SLV Elektronik SLV- 160124/34 Mode D'emploi page 2

ENGLISH
Instruction Manual
for recessed fitting
SLV- 160124/34
Please read carefully and keep for further reference !
1. Use as directed:
This product serves exclusively lighting purposes and may:
only be used with a voltage of 230V ~50Hz.
only be used in dry condition,
not in damp or dirt-endangered rooms.
not in areas of high air humidity.
not be exposed to strong mechanical loads or to strong
contamination.
only be installed and operated after a condition inspection if the
product is dirty or has been moistened through storage.
not be modified or converted.
If these points named above are not adhered to, a short circuit or
electrical shock may occur!
2. Technical Data:
160124
Operating voltage: 230V ~50Hz
Safety class:
Bulb: T16, G5, 24W
Dimensions (B/H/T): 60,5 / 5,8 / 9,8 cm
Recess dim. (B/H/T): 59 / 4,5 / 10 cm
Weight: 1,06 kg
Importer: SLV Elektronik GmbH
3. Installation
The electric connection may be executed only by an electric expert
who is familiar with the valid directives!
Attention: Switch off the power of the mains supply line or
respectively of the connection lead before doing any works!
Use only parts, which belong to the product! Otherwise the product or the
installation might not be sufficiently safe.
Installation place:
The product is intended for recessed wall and ceiling installation.
Make sure that the product is mounted on a stable, even and tilt-fixed
background. Note the minimum distances in the ceiling. The minimum
distances in the wall/ceiling are 5cm to all sides. Do not cover the
product, especially not with insulating materials.
Separate Installation Steps
Mark and cut the opening. Do not damage the mains lead.
Remove the cover on the connection clamp.
Electrical Connection
The product must be able to be separated by an all pole separation
from the current supply.
For electric connection attach the black or brown wire (live conductor)
of the mains lead with the clamp L and the blue wire (neutral
conductor) of the mains lead with the clamp N. The green-yellow wire
(protective conductor) of the mains lead has to be tightly screwed into
the earth clamp of the product.
Put he cover on the connection clamp back on.
Remove the diffuser carefully using a flat tool(e.g. screwdriver).
Move the clamping brackets to the back by turning the screws. Direct the
fitting into the recess. Move the clamping brackets back to the front until
the fitting is kept securely.
Inserting the bulb: Insert the fluorescent tube into the recesses of the
sockets. With a quarter-turn the tube is fixed.
Push the diffuser back onto the fitting.
Pay attention that the product cannot fall down after installation!
The product is now ready for operation.
4. Operation
Information for the user:
Operate the product only if it is working correctly. Switch off the product
with a malfunction immediately and operate it again only after examination
by an electrical specialist. This is the case, when:
visible damages appear.
the product does not work.
smoke, steam or crackling sounds appear.
an overheating is recognisable.
Repairs of the product or work on mains voltage-prominent sections may
only be carried out by qualified electricians.
Attention: Here exists mortal danger from an electric shock!
How to avoid failure and fire risk:
Do not cover the product - provide free air circulation!
Do not hang or fasten anything on the product, especially no decoration.
Never let children play unsupervised with electric products! Children
can not always estimate dangers in dealing with electric energy correctly.
160134
What is to do if a bulb is defect or does not work?
Disconnect the product from power, before you exchange the bulbs.
I
Caution: Let the bulb cool down first before replacement –
T16, G5, 54W
otherwise considerable risk of injury exists because of the hot surface.
120,5 / 5,8/ 9,8 cm
Replace the bulbs only with bulbs of the same data like socket, power
119 / 4,5 / 10
and capacity. Every other sort of bulb can lead to damages of the light.
2,05 kg
Replacing the bulb: see Installation.
5. What else has to be considered?
Disconnect the product from power, before you...
clean or maintain the product.
do any works on the product or its components (electric expert).
:
06/2007 © by SLV Elektronik GmbH
Art.-Nr. 160124/34
Daimlerstr. 21-23, 52531 Übach-Palenberg, Germany
Technical Details are subject to change. Duplication prohibited !