Bosch GTB 12V-11 Professional Notice Originale page 12

12 | English
Intended Use
The power tool is intended for screwing in and loosening
screws.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
A)
(1) Screwdriver bit
(2) Stop sleeve
(3) Adjusting sleeve for screw depth stop
(4) Screw depth stop
(5) Rotational direction switch
(6) Battery release button
A)
(7) Battery
(8) Handle (insulated gripping surface)
(9) Worklight
(10) On/off switch
A)
(11) Universal bit holder
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Cordless screwdriver
Article number
Rated voltage
No-load speed
Maximum torque, hard
screwdriving application ac-
cording to ISO 5393
Tool holder
Screw diameter max.
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– during charging
B)
– during operation and
during storage
Recommended batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
Technical data determined using the battery that comes with the
product.
Noise/Vibration Information
Noise emission values determined according to
EN 62841-2-2.
1 609 92A 4PK | (30.10.2018)
GTB 12V-11
3 601 JE4 0..
V = 12
rpm 0 - 3000
Nm 3
¼" internal
hexagon
mm 4
A)
kg 0.9- 1.1
°C 0 to +45
°C –20 to +50
GBA 12V..
GBA 10.8V..
GAL 12.. CV
AL 11..CV
Typically the A-weighted noise level of the power tool is:
Sound pressure level 74 dB(A); sound power level 85
dB(A). Uncertainty K = 3 dB.
Wear hearing protection
Total vibration values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-2:
2
Screwdriving: a < 2.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Battery Charging
Use only the chargers listed on the accessories page.
u
Only these chargers are matched to the lithium-ion bat-
tery of your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
2
, K = 1.5 m/s .
Bosch Power Tools