Working Advice; Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch AdvancedCut 18 Notice Originale

Insert the charged battery (6) into the battery receptacle un-
til you feel it engage and it is securely locked in place.
Switching on/off
To switch on the power tool, press the lock-off button (3) to
the left or right. Then press the on/off switch (4) and keep it
pressed.
Once the power tool is switched on, you can release the lock-
off button (3).
To switch off the power tool, release the on/off switch (4).
Controlling the sawing speed
You can control the speed of the power tool when switched
on by how hard you press the on/off switch (4). The speed is
continuously variable.
The sawing speed required depends on the material and the
working conditions; it can be ascertained through practical
tests.
It is advisable to reduce the sawing speed when placing the
saw blade on the workpiece.
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or the permitted bat-
tery temperature is exceeded, the electronics of the power
tool will switch off until the temperature returns to within the
optimum operating temperature range.

Working Advice

Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Switch the power tool off immediately if the saw blade
u
becomes blocked.
Always use a sturdy support when working on small or
u
thin workpieces.
Make sure you always cut from front to back (see
u
figure C) or from top to bottom (see figure D) when
sawing.
Do not carry the power tool on your wrist. The suspen-
u
sion strap is intended for storage only (see figure F).
Saw with moderate pressure in order to achieve optimal and
precise cutting results. Applying additional pressure in-
creases performance.
Switch the power tool off immediately if the saw blade jams.
Widen the sawing gap slightly with a suitable tool and pull
the power tool out.
The riving knife (10) prevents sawing against the running
direction of the chain saw.
Recommendations for Optimal Handling of the Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Bosch Power Tools
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.

Maintenance and Service

Maintenance and Cleaning

Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
Always clean the saw blade and saw blade receptacle
u
dry. Use a fine brush (see figure G) to remove more
deeply ingrained dirt.
The saw blade is maintenance-free. The chain of the saw
blade does not need to be oiled.
Clean the saw blade receptacle (13) regularly. To do this,
remove the saw blade from the power tool and gently tap out
the power tool on a flat surface.
If the power tool becomes very dirty, this can lead to serious
faults. For this reason, do not cut materials which generate
large quantities of dust from below or overhead.

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
English | 15
1 609 92A 65Y | (06.11.2020)