Battery Charge Level Indicator; Operation; Main Switch; Control Panel - EINHELL FREELEXO Instructions D'origine

5.9 Battery charge level indicator

Press the button for the battery charge level indi-
cator. The battery charge level indicator indicates
the charge state of the battery by means of 3
LEDs (Fig. 13b).
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs fl ash:
The rechargeable battery has undergone ex-
haustive discharge and is defective. Do not use or
charge a defective rechargeable battery.
5.10 Charging the rechargeable battery with
the charger
1. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(23) into the socket outlet. The green LED will
then begin to fl ash.
2. Insert the rechargeable battery (22) into the
battery charger (23) (Fig. 13a).
3. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The rechargeable battery can become a little
warm during the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charger
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the rechargeable battery when
you notice that the performance of the equipment
drops. Never allow the battery pack to become
fully discharged. This will cause it to develop a
defect.
Anl_FREELEXO_SPK9.indb 38 Anl_FREELEXO_SPK9.indb 38
GB

6. Operation

6.1 Main switch

The robot lawn mower is equipped with a main
switch (7). Use the main switch (7) to switch the
robot lawn mower on (ON) and off (OFF) (Fig. 8).
Once the robot lawn mower has been switched
on, it is locked by a PIN.

6.2 Control panel

The robot lawn mower has already been pro-
grammed at the factory and default settings have
been made for it. However, these can be changed
if required. Even though the factory settings will
be suitable for most gardens, you should still
familiarize yourself with the available options ne-
vertheless.
Explanation of the LEDs on the control panel
(Fig. 9a)
50. Time LEDs: Display of the daily mowing time
51. Lock LED: Display of the button lock
52. Battery LED: Display of the battery charge
level
53. Alarm LED: Display of faults
Explanation of the button options on the con-
trol panel (Fig. 9b)
60. POWER button: Switches the robot lawn mo-
wer on and off
61. "OK" button
62. "SET WORK TIME / 1" button
63. "START / 2" button
64. "HOME / 3" button
65. "4" button / Lock button
6.3 Cutting height adjustment facility
Important! Adjust the cutting height only when
the robot lawn mower has been switched off . Do
this by pressing the STOP button (3). The cutting
height adjustment facility (4) allows the cutting
height of the robot lawn mower to be set to infi ni-
tely adjustable settings between 20 and 60 mm,
which can be viewed on the scale.
If the grass is taller than 60 mm it has to be shor-
tened to a maximum of 60 mm fi rst to avoid expo-
sing the robot lawn mower to excessive load and
adversely aff ecting its operating effi ciency. Use a
conventional lawn mower or trimmer to do this.
After installation has been completed, the cutting
height can be adjusted using the cutting height
adjustment facility (4). Always start with a higher
cutting height and reduce it in small steps until
you reach the desired height.
- 38 -
14.11.2019 12:13:07 14.11.2019 12:13:07