Starting The Charge Process - GRAUPNER ULTRAMAT 14 plus Instructions D'utilisation

Chargeur rapide à grande puissance piloté par micro-processeur pour la charge rapide des accus nicd, nimh, lipo/liio/limn/life et des accus pb
Masquer les pouces Voir aussi pour ULTRAMAT 14 plus:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

3 sec.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
L i P o
m a n u a l
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
C : 2 . 5 A
2 0 0 0 m A h
2
START
sec.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
* * I N F O R M A T I O N * * *
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
B A L A N C E R
C O N .
2
START
sec.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
B A T T E R Y
C H E C K
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
W A I T
P L E A S E . . .
2
sec.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
C H G
2 3 : 4 0
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
L P + 2 . 5 0 A
1 4 . 0 1 7 V
30

10. Starting the charge process

For charging / discharging, or conditioning a pack, select
the desired program as described below, and then set
suitable values.
If the battery does have a balancer connector, connect the
balancer connector to the balancer input (BALANCER
CONNECTOR) of the charger.
Make sure for the right polarity.
From right handed to left side:
Pin 1 (GND): Ground = battery -,
Pin 2 (1): + cell 1, Pin 3 (2): + cell 2, Pin 4 (3): + cell 3,
Pin 5 (4): + cell 4, Pin 6 (5): + cell 5, Pin 7 (6): + cell 6
Connect the two pole power charging cable of the battery to
the charger output - BATTERY + with the right polarity.
Hold the START button pressed in for about two seconds,
and the charger display, if the balancer connector is
connected or not. With connected balancer connector the
single cell voltages can be displayed, see 16..
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
* * I N F O R M A T I O N * * *
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
B A L A N C E R
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
B A T T E R Y
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
W A I T
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
* * * L i P o
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
3
+
INC
START
Press the START button again,
and the charger will assess the
battery.
You can interrupt the charge process at any time with another
0 0 8 6 3
short press on the START button.
Note: if you interrupt the charge process by pressing
the START button, all display parameters are
irretrievably erased.
N O T
2
sec.
C H E C K
P L E A S E . . .
If a Li-battery is connected and the balan-
cer connector is not connected, the char-
2
ger will display the cell count of the Lithium
sec.
pack, which must be corrected manually,
if it is wrong..
c e l l s * * *
c e l l s
( 1 3 . 7 3 V )
-
DEC
C O N
! Caution ! Please
take great care to set
the correct cell
count. and the right
battery type. If you
make a mistake, the
battery could
explode and burst
into flames !

Hide quick links:

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

6464

Table des Matières