Technical Data; Before Starting The Machine; Setting The Cutting Height - EINHELL BG-PT 3041 Mode D'emploi D'origine

Anleitung_BG_PT_3041_SPK1:_
GB

4. Technical data

Engine type
2-stroke engine, air-cooled, chrome cylinder
Engine power (max.)
Displacement
Idle speed of engine
Max. engine speed
Max. twin line speed
Ignition
Drive
Weight (with empty tank)
Long handle length
Cutting circle diameter of line
Cutting line length
Cutting line diameter:
Tank capacity
Spark plug
Sound and vibration were measured in accordance
with DIN EN 11806.
Sound and vibration
L pA sound pressure level
K pA uncertainty
L WA sound power level
K WA uncertainty
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Idling speed (max.)
Vibration emission value a h = 5.8 m/s
K uncertainty = 1.5 m/s
Idling speed (max.)
Vibration emission value a h = 7.9 m/s
K uncertainty = 1.5 m/s 2
Reduce noise generation and vibration to a
minimum!
Use only equipment that is in perfect condition.
Maintain and clean the equipment regularly.
Adopt your way of working to the equipment.
Do not overload the equipment.
Have the equipment checked if necessary.
Switch off the equipment when not in use.
Wear gloves.
18
16.11.2010 11:13 Uhr

5. Before starting the machine

5.1 Montage
Assembling the long handle (Fig. D1 – D3)
0.8 kW/1.1 hp
Slacken the star grip screw (Fig. D1/Item 1) on the
30,3 cc connecting piece on the upper long handle (Fig.
D1/Item 3). Then press the lever catch (Fig. D1/Item
2800 +/- 200 rpm
2) and carefully slide the lower long handle (Fig.
7,400 rpm
D1/Item 4) into the connecting piece on the upper
7,400 rpm
long handle. When doing so, take care to ensure that
Electronic the drive shafts on the insides of the long handles
slide into each other (turn the spool head gently, if
Centrifugal clutch
required) and that the front lug on the lever catch (Fig.
5.6 kg
D2/Item 6) locks into the corresponding hole in the
150 cm
lower long handle (Fig. D2/Item 5). Then retighten the
Ø 41 cm star grip screw (Fig. D1/Item 1) (Fig. D3). To
dismantle, proceed in reverse order.
8.0 m
2.0 mm
Fitting the additional handle (Fig. E1 – E3)
0.8 l
Slacken the wing nut on the fastening screw on the
Champion RCJ6Y handle (Fig. E1/Item 1). Remove the wing nut, washer
(Fig. E1/Item 2) and fastening screw (Fig. E1/Item 3)
from the handle and insert them in the long handle
(Fig. E2). Then screw the handle to the long handle
(Fig. E3).
Fitting the guard hood (Fig. F1 – F3)
Slacken the fastening screw on the guard hood (Fig.
100 dB(A)
F1/Item 1) with the help of the Allen key provided and
3 dB
then remove (Fig. F1). Then attach the guard hood to
the lower long handle (Fig. F2). Screw the guard hood
108 dB(A)
tightly in position with the fastening screw (Fig. F3).
3 dB
Fitting the carrying strap (Fig. G)
The carrying strap is intended to help you work safely
and ergonomically with the power trimmer. Hook the
carrying strap into the fastening eyelet (Fig. G/ Item
A).
2
Check that all moving parts move smoothly
before you start using the machine. Check that
all screws are securely fastened and also check
2
all the safety devices.

5.2 Setting the cutting height

Slip the shoulder strap (Fig. A/17) over the left
shoulder.
Set the length of the shoulder strap in such a way
that the cutting head runs parallel to the ground.
In order to establish the optimum length of the
shoulder strap, you should then make a few
swinging movements without starting the engine
(Fig. I).
Seite 18