Use As Directed - SLV Elektronik AIXLIGHT PRO 51 GU10 Mode D'emploi

SLV Elektronik GmbH
ENGLISH
INSTRUCTION MANUAL FOR
®
AIXLIGHT PRO 51 MODULE GU10
/ GX10
Explanation of the safety warnings:
DANGER: immediate dangerous situation leading to death or severe
injuries when not avoided.
WARNING: possible dangerous situation leading to death or severe
injuries when not avoided.
CAUTION: possible dangerous situation leading to injuries or
material damage when not avoided.
1. NOTES ON SAFETY
Installation, mounting or works on the electrical connection may
only be carried out by an approved electrician.
Do not cover the product - provide free air circulation!
Do not hang or fasten anything on the product, especially no
decoration.
Keep children away from the product.
Operate the product only when it functions properly:
DANGER
In case of a malfunction you may NOT touch the product or operate it
further. Disconnect the product from the power supply by an external
switch or by the fuse.
If touched or further operated there is danger from electric shock,
burning, or fire.
A malfunction exists when:
visible damages appear.
the product does not work properly (e.g. flickering).
smoke, steam or crackling sounds appear.
smell of burning is recognisable.
an overheating is recognisable (e.g. by discolouration of adjacent
surfaces).
Operate the product only after maintenance and examination by an
approved electrician!
2.

USE AS DIRECTED

This product serves exclusively lighting purposes and may:
only be used with a voltage of 230V ~50Hz.
GX10: only be used in combination with a suitable external ballast.
only be operated in combination with AIXLIGHT
FRAME/FRAMELESS.
only be operated when firmly mounted.
only be used in dry condition,
not in damp or dirt-endangered rooms.
not in areas of high air humidity.
not be exposed to strong mechanical loads or to strong
contamination.
only be installed and operated after a condition inspection if the
product is dirty or has been moistened through storage.
not be modified or converted.
3. OPERATION
Exchange the light source always before it reaches its lifespan, to avoid
personal injuries, or damages of the fixture or other objects.
Disconnect the product from the power supply, before you exchange
the bulbs. Let the light source cool down before replacement.
There exists danger of burning!
Use only light sources that are approved for the product. Approved light
sources are indicated on the type label.
Other types of light sources may cause fire risk, damage the product
or lead to malfunction.
Replacing the light source: Pull off the plastic ring from the module.
Remove the used bulb. Insert the new light source with a slight turn to the
right. Apply the plastic ring again.
4. MAINTANANCE AND CARE
Disconnect the product from the power supply and let it cool down,
before you clean the product.
If disregarded there may be danger of electric shock or by burning
when cleaning the product.
Cleaning: Clean the product on a regular basis using a slightly
moistened, soft and fluff-free cloth.
5. ADDITIONAL IMPORTANT NOTES
Storage: The product must be stored in a dry and clean environment. Do
not strain the product mechanically during storage.
Warranty: In case of a warranty contact your dealer.
Disposal: Notes on the correct disposal in Germany are found on
www.slv.de.
6. INSTALLATION
Switch off the mains or respectively the connection lead before doing
.
any works
There exists mortal danger from an electric shock.
Use only parts, which are supplied with the product or are described as
accessories!
Otherwise the product or the whole installation may not be secure.
Danger for life or danger of fire may exist!
Inspect the product for loose parts inside the housing. When there are
loose parts inside the housing and these are not explicitly described the
product may not be installed or operated.
The housing maybe voltage-carrying. Danger of electric shock!
Use the supplied fastening material only when it is suited for the
installation background. If this is not the case use only fastening material
suiting the installation background.
®
PRO 51
When using fastening material that is not suitable there may be
danger from falling objects.
CAUTION
WARNING
(only by an approved electrician)
WARNING
Unpacking
Carefully take the product out of the packaging removing any transport
safeguards.
Before disposal of the packaging material make sure that all
components of the product are removed.
Installation place
The product is exclusively suited for installation into AIXLIGHT
FRAME/FRAMELESS, and may not be used otherwise.
The light exit should be placed at least so far from the illuminated surface,
as indicated as minimum distance on the type plate of the luminaire:
. Pay special caution to easily inflammable objects (e.g.
curtains).
Separate Installation Steps
Inserting the bulb (1): Pull off the plastic ring from the module. Insert the
light source with a slight turn to the right. Apply the plastic ring again.
®
Inserting the module into AIXLIGHT PRO 51 FRAME/FRAMELESS
See the supplied manual of these products. Ensure the secure hold of the
product!
Electrical Connection (2):
The product must be able to be separated by an all pole separation from
the current supply.
Open the connection box.
GU10:
For electric connection attach the black or brown wire (live conductor) of
the mains supply with the clamp L and the blue wire (neutral conductor)
of the mains supply with the clamp N.
GX10:
IInstall a suitable ballast for metal vapour discharge lamps according to
the manufacturers instructions.
Connect the module to the ballast. Note the right connection. Use only
a suitable high-voltage cord ( 5kV) for this connection (e.g. SIHSI-
J,Cu uz,3x0,75mm²).
Direct all leads through the corresponding strain reliefs.
Close the connection box.
art.-no. 115414/24 06/2008
©
SLV Elektronik GmbH, Daimlerstr. 21-23, 52531 Übach-Palenberg,
Germany, Tel. +49 (0)2451 4833-0
Technical Details are subject to change.
®
PRO 51