Technical Data; Before Starting The Equipment - EINHELL G-ET 5531 Mode D'emploi D'origine

Anleitung_RG_ET_5531_SPK7__ 10.06.13 11:41 Seite 14
GB

5. Technical data

Mains voltage
Power
Cutting circle
Revolutions n
0
Cutting line diameter
Weight
Sound and vibration
L sound pressure level
pA
K uncertainty
pA
L sound power level
WA
K uncertainty
WA
Sound pressure level at the operator's ear 84 dB(A)
K uncertainty
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration emission value a ≤ 2,5 m/s
h
K uncertainty = 1,5 m/s 2
Warning!
The specified vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equipment
is used and may exceed the specified value in
exceptional circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
n
order.
Service and clean the appliance regularly.
n
Adapt your working style to suit the appliance.
n
Do not overload the appliance.
n
Have the appliance serviced whenever
n
necessary.
Switch the appliance off when it is not in use.
n
Wear protective gloves.
n
14
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual
230 V ~ 50 Hz
risks cannot be rules out. The following hazards
550 W may arise in connection with the equipment's
construction and layout:
Diameter 31 cm
1. Lung damage if no suitable protective dust mask
9,200 rpm
is used.
1.4 mm 2. Damage to hearing if no suitable ear protection is
used.
2.7 kg
3. Health damage caused by hand-arm vibrations if
the equipment is used over a prolonged period or
is not properly guided and maintained.
73 dB(A)

6. Before starting the equipment

3 dB
93 dB(A) 6.1 Assembling the grass trimmer (Fig. 3-4c)
Remove the fastening set from the additional
n
3 dB
handle (Fig. 2/Item 4).
Push the additional handle (Figure 3/Item 4) onto
n
3 dB(A)
the top handlebar (Figure 3/Item 7) and secure
with the previously removed fastening set.
Place the guard hood (Figure 4a/Item 12) on the
n
motor head as shown in Figure 4a.
Fold the guard hood (Figure 4b/Item 12) together
n
2
as shown in Figure 4b.
Secure with screw (Figure 4c/Item 14).
n
Remove the fastening set from the guide wheels
n
(Figure 2/Item 15).
Fit the guide wheels onto the bottom handlebar
n
and secure with the previously removed fastening
set (Figure 4d).
6.2 Height adjustment (Fig. 5b)
You can set your optimal working position by
adjusting the height.
Undo the lock for the handlebar adjustment
n
(Figure 5b/Item 6).
Pull out the bottom handlebar (Figure 5b/Item 8)
n
to the required length.
Refasten the lock for the handlebar adjustment
n
(Figure 5b/Item 6).
6.3 Adjusting the additional handle:
Place the grass trimmer on a firm surface. Undo the
lock of the additional handle (Fig. 3/Item 5) and move
the additional handle to its optimal position. Lock the
handle in place by retightening the lock.
6.4 Using the distance bracket
If necessary the distance bracket (Figure 5c/Item 9)
can be swung down until it engages. Use the distance
bracket, for example, to cut around plants.