Denon DJ SC5000 PRIME Guide D'utilisation page 13

To skip to the previous or next track, press one of the Track Skip / buttons.
To return to the beginning of a track, press Track Skip  in the middle of a paused track.
To scan quickly through the track, press and hold Shift and then press one of the Beat Jump buttons.
To enable or disable Slip Mode, press Slip. In Slip Mode, you can jump to cue points, use the platters, or pause the track
while the track's timeline continues (the lower half of the waveform in the touchscreen will continue moving forward).
When you stop whatever action you are performing, the track will resume normal playback from where it would have
been if you had never done anything (i.e., as if the track had been playing forward the whole time).
To jump to a specific location in the track:
•
If Needle Lock is disabled: tap the desired location in the track overview.
•
If Needle Lock is enabled: pause playback and then tap the desired location in the track overview. Alternatively,
make sure the platter is in Vinyl Mode (press Vinyl so it is lit), touch the top of the platter, and tap the desired
location in the track overview.
See Control Center > User Profile
To zoom in and out of the waveform, place two fingers on the display and spread them apart or pinch them together.
Alternatively, turn the Select/Load knob.
Looping & Beat-Jumping
To create and activate an auto loop, press the Auto Loop knob.
To set the auto loop length, turn the Auto Loop knob to select the number of beats: 1/32, 1/16, 1/8, 1/4, 1/2, 1, 2, 4, 8,
16, 32, or 64.
To create and activate a manual loop, press Loop In to set the start point, and then press Loop Out to set the end
point. The loop will be activated immediately, and the loop will be indicated as a shaded area in the waveform and
track overview.
To deactivate a loop, press the Auto Loop knob.
To move the loop, press and hold Shift and turn the Auto Loop knob while the loop is activated.
To double or halve the length of a loop, turn the Auto Loop knob while the loop is activated.
To manually edit the beginning or end of a loop, press Loop In or Loop Out, respectively, and then move the platter
left or right to shorten or extend the loop region. Commit the edit by pressing Loop In or Loop Out again.
To beat-jump through a track, press one of the Beat Jump buttons. Each press will skip through the track by the
length of an auto loop, which you can set by turning the Auto Loop knob.
Syncing & Pitch Adjustment
To activate sync, press Sync on the unit that you want to control the BPM, which becomes the "primary." After Sync is
activated on that unit, press Sync on any additional units. The tempo of each unit will immediately synchronize to
match the tempo of the primary unit.
The Sync state icon in the display will indicate the current status:
Sync Off: Sync is deactivated.
Tempo Sync: Only the tempo is synced (the BPM will match that of the primary unit).
Bar/Beat Sync: The tempo will be synced, and the track will be automatically bar- or beat-matched with the
track on the primary unit, depending on the Sync Mode setting.
To deactivate sync on an SC5000 PRIME unit, press Sync again, or press and hold Shift and press Sync, depending
on the setting of Sync Button Action in the
To set a different SC5000 PRIME unit as the master, press Master. All connected SC5000 PRIME units with Sync
activated will use the tempo of this unit. You can also tap Sync Lead on the touchscreen to select which layer on the
primary unit is used for sync.
To adjust the track's pitch, move the pitch fader. You can do this only when the deck is not synced.
Important: If Sync is activated, moving the pitch fader on the "primary" SC5000 PRIME unit will change the speed of
all synced units, while moving the pitch fader on other units will do nothing.
To adjust the track's pitch momentarily, press and hold one of the Pitch Bend –/+ buttons.
To adjust the range of the pitch fader, press and hold Shift and press one of the Pitch Bend –/+ buttons to select
+4%, 8%, 10%, 20%, 50%, or 100%.
To reset the track's pitch to 0%, press Shift+Key Lock/Pitch Reset. The track's pitch will return to its original pitch
(0%) regardless of the position of the pitch fader.
To adjust the track's key, tap the key on the touchscreen to open the Key Change Menu.
to learn about Needle Lock.
User Profile.
13