INSTRUCTIONS ON ASSEMBLY AND USE
EN
CONGRATULATIONS ON PURCHASING THIS PRODUCT!
Please read these instructions carefully. The instructions are an integral component of the
product. Therefore, please store them and the packaging carefully in case questions arise in
the future. Please always include these instructions when handing on the product to a third
party. This product must be assembled by an adult. This product is designed for private/
domestic use only. This product is not designed for commercial/industrial use. The use of
the product requires certain capabilities and skills. Always adjust according to the age of the
user and use for the purpose it has been designed for.
TECHNICAL SPECIFICATIONS
Item:
Child's bicycle 16"
Item number:
10275, 10541 | 10278, 10543
Maximum assembly dimensions: ca. 114 x 52 x 70 cm | ca. 117 x 55 x 72 cm
Maximum saddle height:
60 cm | 59 cm
Minimum saddle height:
55.5 cm | 55 cm
Maximum user weight:
30 kg | 30 kg
Maximum weight:
40.1 kg | 59.5 kg
Purpose:
Bike for locomotion of children with a max. user weight of
30 kg on non-public roads
If you have assembly problems or would like further information on the product, we have all
you need and more at http://www.hudora.de/.
CONTENTS
1 x Bicycle frame with rear wheel
1 x Saddle with saddle rod
1 x Front mudguard
1 x Basket (only 10278 | 10543)
Other items are meant to facilitate safe transportation and are not required for the installa-
tion and use of the product.
SAFETY INSTRUCTIONS
The bicycle should only ever be used under adult supervision. Please use the bicycle in sui-
table play areas only. It does not correspond with road traffic regulations. It may not be used
on the road and should not be used in the dark. The bicycle corresponds to the provisions
of the European norm EN ISO 8098. When used as intended, risks during play are excluded
to a large degree. However, please consider that unforeseeable situations and risks can
arise due to children's natural play instinct and temperament and are not the manufacturer's
responsibility. Therefore, please instruct your children on the correct use of the bicycle and
make them aware of any possible risks. Explain the main braking system, the coaster in par-
ticular. Children should wear protective clothing (helmets, reflectors, etc.) and closed shoes.
Please do not use the bicycle in the proximity of stairs, slopes, steep ground, swimming pools
or other areas of open water. Please consider that in case of a wet road, the braking distance
is longer. Stairs in the vicinity should be blocked off so that children can never cycle down
them on the bicycle. Please take caution when you are doing maintenance or repair work on
the bicycle. There is risk of entrapment.
INSTRUCTIONS ON ASSEMBLY
Take the individual parts out of the box and check that you have everything.
COMPONENTS (FIG. 1)
1
Handlebar with brake and bowden cable
3
Handlebar head with steering ring
5
Front mudguard
7
Front wheel
9
Pedal
11 Saddle with saddle rod
ASSEMBLING THE SADDLE (FIG. 2)
Stick the saddle rod into the saddle post and adjust it to the required height. Tighten the nut
(A). Note that the screw should be tightened with a force of 10 Nm. Please ensure that the
saddle post is not mounted higher than indicated by the marking. The height of the saddle
should be set such that the child can reach the ground with the tippy-toes of both feet (B).
ASSEMBLING THE HANDLEBARS (FIG. 3)
Stick the handlebars into the stem of the frame. Make sure that the fork is properly inserted
into the stem. The marking of the maximum height setting should not be visible. Lock the
handlebars in place at the right height and attach the handlebar clamp. The screw should
be tightened with a force of 10 Nm. The right seating position for children is: the handlebars
should be mounted a little higher than the saddle. Please heed the safety markings!
All images are examples of the design.
1 x
Handlebar with brake and bowden cable
1 x
Handlebar cushion
2 x
Pedals
1 x
Front wheel
2
Handlebar cushion
4
Brake lever
6
Front wheel fork
8
Bicycle frame with rear wheel
10 Pedal sleeve
FRONT WHEEL ASSEMBLY (FIG. 4)
After you remove the nut and washer from the front wheel axle, push the front wheel from
the bottom into the front fork. If you are unable to push the wheel through the brake shoe,
loosen the brake cable and allow the brake shoe to spread apart. After that, tighten the
brake shoe again to ensure that the brakes can flawlessly grab the rim. The distance should
be approx. 1.5 mm. As shown in the image, place the washer on the axle and alternately,
but symmetrically, screw the nuts into place. The screwing should be done with a force of
18 Nm. Before the nuts are completely fastened, ensure that the wheel runs free and sits
symmetrically on the fork.
ASSEMBLING THE PEDALS (FIG. 5)
Screw the pedals into the pedal cranks. The right pedal is marked with (R) and the left with
(L). The right pedal (R) is tightly screwed into place in a clockwise direction, i.e. to the right.
The left pedal (L) is tightly screwed into place in an anti-clockwise direction, i.e. to the left.
ATTACHING THE FRONT MUDGUARD (FIG. 6)
C. Lock nut | D. Mudguard | E. Washer | F. Fork | G. Front brake
Remove the nut from the brake mount in order to attach the mudguard. Attach the mudguard
and tighten the screws once again so that the mudguard can no longer be turned. Check in
regular intervals that the mudguard is screwed on tightly.
ATTACHING THE BASKET – ONLY 10278 | 10543 (FIG. 7)
Thread the two plastic strips in the two double slits in the basket and pull them up by half.
Hold the basket on the handlebars, and enclose it with the plastic strip. By turning the head
of the strips they should fit through the openings in the strips. Pull the strip down and hide
the loose ends.
USAGE INSTRUCTIONS
ADJUSTING THE BRAKES (FIG. 8)
If you need to adjust the brakes, use two wrenches – the inner nut (J) is held with one wrench
and then the other is used to loosen the outer nut. Now carefully turn the inner screw in a
clockwise direction in order to loosen it or in an anti-clockwise direction in order to tighten it,
depending on the brake's fastened state. Now keep the inner screw (J) in position and tighten
the outer screw (K) so that the screws are locked in place against one another with the nuts.
If the distance between the brake shoes and the rim is too big, loosen the lock nut (H) and
turn the adjusting screw (I) until the distance between the brake shoes and rim is reduced to
approx. 1.5 mm. Now tighten the lock nut. If this is not enough, tighten the brake cable (L),
so the brake pads located at the correct distance from the rim .
Warning! If you have problems with adjusting the brakes or when you encounter general
problems, do not use the bicycle until these problems are well solved. Please consider that
the front brake is operated by the right hand. The coaster is operated by the foot when the
pedal is pushed backwards instead of coming forward. In case of sudden or hard braking do
not only used the hand brake. The danger excists that you tumble forward. After you have as-
sembled all components, make sure that all connections are tightly screwed together before
allowing your child to play with the bicycle.
MAINTENANCE AND STORAGE
Use a dry or damp cloth only to clean the product; do not use special cleaning agents! Check
the product for damage or traces of wear and tear before and after each use. Do not make
any structural changes. For your own safety, please use original spare parts only. These can
be sourced from HUDORA. If parts become damaged or if sharp edges or corners should
develop, the product may not be used any more. If in any doubt, please contact our service
team (http://www.hudora.de/service/). Store the product in a safe place where it is protec-
ted from the elements, cannot be damaged, and cannot injure anyone.
When you assemble the saddle, handlebars and wheels, please observe the torque recom-
mended in this manual. Check the product for damage or traces of wear and tear before and
after each use. Focus your attention mainly on the pads/brakes, wheels, rims and steering-
wheel. If any of these parts is worn, it should be replaced immediately. The chain should be
regularly oiled. Please use a suitable chain oil for this only. Also check the tension of the chain
(max. 1.5 cm slack). If there are problems with the chain or brakes, the bike can not be used
until this is well repaired.
DISPOSAL ADVICE
At the end of the product's life, please dispose of it at an appropriate collection point provided
in your area. Local waste management companies will be able to answer your questions on
this.
SERVICE
We make every effort to deliver faultless products. If faults do arise however, we put just as
much effort into rectifying them. You can find numerous information on the product, repla-
cement parts, solutions to problems and lost assembly manuals at http://www.hudora.de/
service/.
4/8