SEVERIN PG 8106 SEVO GT Mode D'emploi page 13

Rotary control - light ring
The light ring indicates the current operating mode:
No light:
The unit is in sleep mode.
Blue light:
The unit is in stand-by mode.
Flashing:
The grill rack has not yet reached the selected temperature.
The unit is heating up or cooling down.
Steady:
The selected temperature has been reached.
Orange:
Grilling at 80-320 °C
Red:
Boost-zone 330-500 °C
Timer
The timer is used to monitor the grilling time. It can be set
from 1 min to 23 h 59 mins. Beep signals indicate that the
running time has elapsed; the heating element remains
switched on.
∙ Turn the rotary control until
∙ P ress the rotary control briefly and turn to select the
hours.
∙ P ress the rotary control briefly and adjust the minutes.
∙ C onfirm the time setting by briefly pressing the control.
The colon starts flashing; once the time has elapsed,
beep signals are heard.
∙ To return to stand-by mode, press the rotary control for
two seconds.
∙ Alternatively, set the timer to 0:00, and press the control
briefly to return to stand-by mode.
∙ If the heating is switched off after the timer is set, the
appliance will change to sleep-mode 5 minutes after the
last input, i.e. the timer is switched off.
∙ If the timer is set with the heating already off, it will
continue until the pre-selected time is reached, when the
unit changes to sleep-mode.
Grilling at 80-320 °C
To grill sausages, poultry, fish etc. For finishing or keeping
warm steaks.
The entire grill surface is heated.
∙ Turn the rotary control until
∙ P ress the rotary control briefly and turn to select the
desired temperature. Press briefly to confirm.
∙ T he ring starts flashing orange and the appliance is
heating up.
∙ Once the selected temperature has been reached, the
ring shows steady orange.
∙ Place the food on the grill surface.
∙ Close the cover, if desired.
lights up.
lights up.
'Boost-zone' grilling 330-500 °C
For searing or light grilling of steaks.
The boost-zone is located to the right; the left side is
heated to 320 °C.
∙ Turn the rotary control until
∙ P ress the rotary control briefly and turn to select the
desired temperature. Press briefly to confirm.
∙ T he ring starts flashing red and the appliance is heating
up.
∙ Once the selected temperature has been reached, the
ring shows steady red.
∙ Place the food on the boost-zone.
Note:
Do not close the cover during Boost-zone grilling. The
Boost-zone function is automatically de-activated when
the cover is closed.
∙ For subsequent cooking, lower the temperature or shift
the food to the left on the grill surface.
Grilling with the core thermometer
∙ Scope of supply: 1 piece
Other core thermometers are available under item no.
8126.
∙ Caution: The core thermometers heat up during use.
Use suitable protection, eg barbecue gloves.
∙ Fit the thermometer plugs into the sockets at the lower
left of the junction box . To prevent the appliance from
switching off, ensure that the box is not lifted up and
stays properly connected.
∙ Select the desired grill function and temperature.
∙ Once pre-heating is complete and the ring shows a
steady light, put on the food.
∙ Push the tips of the thermometers into the centre of the
food.
∙ U se the rotary control to set the desired core
temperature or
∙ The display shows the respective current core
temperature.
∙ When using the cover during grilling, the core-
thermometer cables should be routed through the cable
leads on either side of the cover (see diagram 9).
∙ Once the pre-set core temperature on one thermometer
is reached, three long beep signals are heard.
∙ Remove the respective thermometer and take off the
food.
Note:
The grill plate remains on even after the pre-set core
temperature has been reached.
Stand-by mode
∙ To switch off the heating and return to stand-by mode,
press the rotary control for two seconds.
∙ A lternatively, press the control briefly, set the
temperature to 00 and press again briefly to return to
stand-by mode.
lights up.
. Press briefly to confirm.
13