Güde GGH 35 TRI Mode D'emploi Original page 10

GB
Introduction
Please read thoroughly this operation manual and
attached safety instructions to enjoy your new gas hot air
turbine. We further recommend to retain the operation
manual for future references. We reserve right to make
technical changes for the purpose of improvement in the
course of continuous product development.
This is the original operation manual.
Device description (figure A+B)
1. Gas hot air turbine with stainless steel housing
2. Gas controller
3. Gas hose connector
4. ON/OFF switch – heating/fan
5. Indicator
6. Reset button
7. Gas hose with connectors
8. Pressure reducing valve
9. Hose breaking protection
10. Thermostat
11. Digital room temperature indicator (actual value)
12. Digital required temperature indicator (required
value)
13. Front cover
14. Handle
Technical data
GGH 35 TRI
Voltage/frequency:
Heating output:
Consumption:
Operating pressure:
Fan output:
Gas type:
Feeder cable length:
Weight:
Use as designated
The gas hot air turbine has exclusively been designed for
heating and drying out purposes in the building industry
(fabrics), agriculture, storage spaces (ventilated rooms
only), etc.
The appliance may only be used as designated. The
manufacturer cannot be held liable for any damage
if provisions of the generally applicable regulations
or provisions of these Operating Instructions are not
followed.
General safety instructions
Read and observe all instructions contained herein before
commissioning and operation of the device.
Keep the safety instructions for future reference!
Safe work
Keep your workplace tidy!
Disorder on workplace may result in injuries.
Consider surrounding conditions!
Do not expose to rain.
Do not use in moist or wet environment.
Provide good lighting.
Do not use close to flammable liquids or gases (except for
substances required for operation - here propane/butane).
230 V~50 Hz
22-35 kW/
18.900-30.000
kcal.per hour
(controllable)
2.0-2.5 kg per hour
1500 mbar
707 m³ per hour
Propane-butane
1.6 m
7.8 kg
Keep other persons in a safe distance!
Other persons, particularly children, may not touch the
device and power cable. Keep them in a sufficient distance
from your workplace.
Store your device properly!
The device, if not used, should be stored in a dry and
closed space, out of reach of children.
Do not overload your device!
You will work better and more safely if the device is used
at performance power for which it is designed to.
Use correct device!
Do not use the device for purposes other than intended.
Secure your device correctly!
Connect your device according to instructions in
"Assembly" section.
Take care of your tools!
Observe maintenance directions and instructions.
Check tool cable regularly and ask an authorized specialist
to replace the same if damaged.
Check extension cable regularly and replace, if damaged.
Keep handles dry, without traces of oils and greases.
Be careful!
Be aware of what you are doing. Approach your work with
sound mind. Do not use the device if you are tired.
Check the device for damage!
Before use, check thoroughly all safeguards and slightly
damaged parts if they are still functioning properly.
Check whether rotary parts operate freely and not jammed
or damaged.
All parts must be installed properly and must comply with
conditions so that perfect operation of the device is
ensured.
Damaged safeguards and parts must be either repaired or
replaced by an authorized workshop, unless specified
otherwise in this operation manual.
Replace damaged switches in a service workshop. Do not
use the devices with malfunctioning ON/OFF switch.
WARNING!
Use of non-compliant accessories may result in an injury.
Have your device repaired by an electrician only!
This device complies to applicable safety provisions.
Repairs may be performed by an electrician with the use of
genuine spare parts, otherwise the user may be exposed
to injury hazard.
Safety instructions specific for this device
•
This device may be used outside only and in
well ventilated areas, however, it must be
protected against moisture or rain.
•
Gas cylinder must be always protected against
freeze and minus temperature at any times.
•
The device may be used for heating only.
• Attention! Open flame tightness test is
strictly prohibited.
• Do not operate under ground level.
•
Do not move and lift the device if in use.
• Radiation area must be at least 3 metres from
persons and all flammable substances.
• Keep 50 cm distance between walls and rear or
sides of the device.
• If gas leaks (smell), close the gas cylinder valve
immediately and keep the device out of reach of
all flammable sources.
• Check tightness of all connections.