JB Systems Magic LED II Mode D'emploi page 5

ENGLISH
DMX-CONFIGURATION OF MYSTERY LED II & MAGIC LED II:
1 CHANNEL MODE
Two DMX-modes are available: 1CH and 3CH mode:
1 channel mode:
Extremely user friendly mode: you only need 1 DMX channel to choose 1 of the 11 preprogrammed
sound chases or you can use our Effect commander to switch the unit ON/OFF (no switch pack needed).
3 channel mode:
You can take full control of all functions of
the effect.
 Channel 1: control for dimmer + strobe
 Channel 2: select one of the 32 available
color combinations.
 Channel 3: Rotation speed and direction
HOW TO SETUP:
MAIN MENU:
 To select any of the menu options, press the
MENU button up to when the required one is
shown on the display.
 Select the function with the ENTER button.
The display will blink.
 Use DOWN and UP button to choose the
desired menu option.
 Once the required menu option is selected,
press the ENTER button to select. To go back
to the functions without any change press the
MENU button or just wait 8 seconds. The
menu structure is shown below.
JB SYSTEMS
®
OPERATION MANUAL
3 CHANNEL MODE
5/55 MAGIC LED II ~ MYSTERY LED II
ENGLISH
DMX512 Address Setting
Used to set the starting address in a DMX setup.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to change the DMX512 address.
 Once
the correct address shows on
(or automatically return to the main functions without any change after 8 seconds)
 Press the MENU button for about 2 seconds to return to running mode.
Channel Mode
Used to set the number of DMX-channels.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select the
 Once the mode is selected, press the ENTER button to setup
(or automatically return to the main functions without any change after 8 seconds)
 Press the MENU button for about 2 seconds to return to running mode.
Working Mode
Used to set the unit in master or slave mode.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the current working mode starts blinking in the display
 Use the DOWN and UP buttons to select
(2 light show – slave in anti-sync with the master).
 Once the mode is selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
 Press the MENU button for about 2 seconds to return to running mode.
Show Mode
Used to choose to select one of the preprogrammed shows when used in standalone or master/slave
mode.
 Press the MENU button until
is showing on the display.
 Press the ENTER button, the current show starts blinking in the display.
 Use DOWN and UP buttons to select one of the 8 preprogrammed shows
(show 8)
 Once the right show blinks on the display, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
 Press the MENU button for about 2 seconds to return to running mode.
Sound Mode
Used to choose the desired sound mode to trigger the shows.
 Press the MENU button until is shown on the display.
 Press the ENTER button to select.
 Use DOWN and UP button to select one of the available modes:

(sound mode ON)  the shows are triggered by the internal microphone.

(sound mode OFF)  the shows are triggered by the speed selected with the shows.
 Once the right mode is selected, press the ENTER button to confirm.
 Press the MENU button for about 2 seconds to return to running mode.
JB SYSTEMS
®
OPERATION MANUAL
the display, press the ENTER button to
(1 Channel) or (3 Channel) mode.
(master), (slave in sync with the master) or
(show 0) to
6/55 MAGIC LED II ~ MYSTERY LED II
save it.