Makita DLS713 Manuel D'instruction page 14

1 2
001555
There are crown and cove molding joints which are
made to fit "Inside" 90° corners ((1) and (2) in Fig.
A) and "Outside" 90° corners ((3) and (4) in Fig. A).
(1) (2) (3) (4)
1 2
Fig.A
001556
1
(2)
(1)
(4)
(2)
(3)
(1)
(2)
(1)
001557
Measuring
Measure the wall length and adjust workpiece on table
to cut wall contact edge to desired length. Always make
sure that cut workpiece length at the back of the
workpiece is the same as wall length. Adjust cut length
for angle of cut. Always use several pieces for test cuts
to check the saw angles.
When cutting crown and cove moldings, set the bevel
angle and miter angle as indicated in the table (A) and
position the moldings on the top surface of the saw
base as indicated in the table (B).
In the case of left bevel cut
Molding
position in
52/38° type
Fig. A
(1)
For inside
corner
(2)
Left 33.9°
(3)
For outside
corner
(4)
006361
1. 52/38 ﾟ type
crown molding
2. 45 ﾟ type crown
molding
3. 45 ﾟ type cove
molding
3
1. Inside corner
2. Outside corner
1. Inside corner
2. Outside corner
(1)
(2)
2
(1)
(2)
Table (A)
Bevel angle Miter angle
45° type 52/38° type
Right 31.6°
Left 30° Left 31.6°
Right 31.6°
For inside
corner
For
outside
corner
006362
In the case of right bevel cut
For inside
corner
For outside
corner
006363
For inside
corner
For
outside
corner
006364
45° type
Right 35.3°
Left 35.3°
Right 35.3°
14
Table (B)
Molding
Molding edge against
position in
guide fence
Fig. A
Ceiling contact edge should
(1)
be against guide fence.
(2)
Wall contact edge should be
against guide fence.
(3)
Ceiling contact edge should
(4)
be against guide fence.
Example:
In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
Tilt and secure bevel angle setting to
•
33.9° LEFT.
Adjust and secure miter angle setting to
•
31.6° RIGHT.
Lay crown molding with its broad back
•
(hidden) surface down on the turn base
with its CEILING CONTACT EDGE
against the guide fence on the saw.
The finished piece to be used will
•
always be on the LEFT side of the blade
after the cut has been made.
Table (A)
Bevel angle
Molding
position in
52/38° type 45° type
Fig. A
(1)
(2)
Right 33.9° Right 30°
(3)
(4)
Table (B)
Molding
Molding edge against
position in
guide fence
Fig. A
Wall contact edge should be
(1)
against guide fence.
(2)
Ceiling contact edge should
be against guide fence.
(3)
Wall contact edge should be
(4)
against guide fence.
Finished piece
Finished piece
will be on the
Left side of
blade.
Finished piece
will be on the
Right side of
blade.
Miter angle
52/38° type 45° type
Right 31.6° Right 35.3°
Left 31.6° Left 35.3°
Right 31.6° Right 35.3°
Finished piece
Finished piece
will be on the
Right side of
blade.
Finished piece
will be on the
Left side of
blade.