FALMEC lumen Mode D'emploi page 17

• With external exhaust (suction) versions, it is possible to insert extension (H) with the slots facing downwards so that they are not visible when
the installation height allows it.
F
Phase page 5
• Slide the extension (H) until it is positioned at the desired height (Fig.
• Following what is indicated in Fig.
• Place the bracket (L) on the wall by following the line drawn on it. With a spirit level, check the horizontal alignment and mark the 2 drilling points
at the ends (Fig. ).
3
• Drill the holes, insert 2 expansion plugs (ø 6mm) and fasten the bracket (L) with the relative screws (V4) (Fig.
• Tighten the extension (H) to the bracket (L) using screws (V5) (Fig.
• Electrically power the hood in accordance with regulations in force.
OPERATION
WHEN SHOULD THE HOOD BE SWITCHED ON AND OFF?
Switch on the hood at least one minute before starting to cook: this enhances the airlow to convey fumes and vapours towards the suction surface.
After cooking, leave the hood operating until complete extraction of all vapours and odours. If required, by means of the Timer function, it is possible
to set hood auto switch-of after 15 minutes of operation.
WHICH SPEED IS TO BE SELECTED?
The irst speed is a low consumption energy-saving way of keeping the air clean, the second speed is used in normal conditions, and the third
speed is used when there are strong odours and vapours.
WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?
The hood is assembled with two diferent types of ilters: metal ones (washable) and active carbon ones (non-washable). The former must be
cleaned every 30 hours of use (the ixed red light
pending on the use of the hood. For further information, please read the chapter regarding "Maintenance" on page 18.
USE OF ELECTRONIC PUSH BUTTON CONTROL PANEL
Timer/Filters alarm
Pressing the key with the motor active at any speed activates
the Timer function: this function determines the auto switch-
of of the hood after 15 minutes of operation. Activation of
the function is signalled by a RED lashing light.
With the Timer function active, the hood can still be switched
of by the user at any time by pressing the key
will be automatically disabled and the RED light will turn of.
Should the speed be changed with the Timer function active,
the latter will be automatically disabled.
On the other hand, ignition of the ixed RED light indicates a
grease ilter alarm: this alarm notiies that it is time to wash
the metal anti-grease ilters (the alarm is triggered after approx-
imately 30 hours of use). After cleaning the ilters, disable the
alarm and reset the counters by keeping the key pressed for 3
seconds.
To disassemble and assemble the anti-grease metal ilters,
refer to the instructions on drawing
LIGHTING
The hood has luorescent lamp lighting.
If the lamp ever needs to be replaced:
disconnect the appliance from the electrical mains power supply by unplugging it or turning of the main switch;
•
Phase
remove the covering element (N) (Fig.
•
• take out the blown luorescent tube (M) (Fig.
• put in a new luorescent lamp by performing, in reverse order, the operations described in Fig.
The new luorescent lamp must be identical to the old one!
• put the covering element back in (N) performing, in reverse order, the operations described in Fig.
• connect the appliance back up to the electrical power mains.
, draw a line on the wall that will be used to position the bracket (L) correctly.
2
indicates that they need to be washed), the latter are to be replaced every 3-4 months, de-
: the function
G
on page 6.
I
page 6
and );
3 4
).
1
).
5
Mode button (ON/OFF)
Pressing the key switches on (or of ) the hood motor: it starts at
the previously selected speed prior to switching it of (desired
speed function). Should you wish to use a diferent speed, set
if by using the + and - keys.
Button +
By pressing the key, the motor speed increases. Speeds 1, 2 and
3 are displayed by the number of LEDs switched on, excluding
the light and timer LEDs.
The + key in the version with 4 speeds has an intermittent light:
the 4th speed or intensity is timed and after approximately 7
minutes the motor automatically switches to 3rd speed.
Button -
By pressing the key, the motor speed reduces. Speeds 1, 2 and
3 are displayed by the number of LEDs switched on, excluding
the light and timer LEDs.
Light button
ON: light on (lit button) OFF: light of
and );
1 2
and
3
17
).
4
;
4
and ;
1 2