Low Emission Fire Lighting; Normal Operation; Operation During Transition Periods - Nordica INSERTO 50 Crystal Manuel Utilisateur

LOW EMIssION FIRE LIgHTINg

Smokeless combustion is a way of lighting a fire able to significantly reduce the emission of harmful substances. The wood burns gradually
from the top downwards, so combustion is slower and more controlled. Burnt gases pass through the high temperatures of the flame and
therefore burn almost completely.
Place the logs in the hearth a certain distance apart as shown in the
or vertically in the case of tall narrow combustion chambers. Place the fire starter module on top of the pile, arranging the first logs in the
module at right angles to the pile of wood.
Fire sTARTER MODULE
This fire starter module replaces a paper or cardboard starter.
Prepare four logs, 20 cm long with a cross section of 3 cm by 3 cm
right angles, with the fire lighter (wax impregnated wood fibre for example) in the middle. The fire can be lit with a match.
If you want, you can use thinner pieces of wood. In this case, you will need a larger quantity.
Keep the flue gas exhaust valve and combustion air regulator open (1A - 2A). After lighting the fire, leave the combustion air regulator open
in the position shown in the Picture.
IMPORTANT:
• do not add further wood between one complete load and the next;
• do not suffocate the fire by closing the air intakes;
• regular cleaning by a chimney sweep reduces fine particle emissions.
These instructions are backed by ENERGIA Legno SVIZZERA

NORMAL OPERATION

After having positioned the registers correctly, insert the indicated hourly wood load avoiding overloads that cause anomalous stresses and
deformations. You should always use the product with the door closed in order to avoid damages due to overheating (forge effect).
The inobservance of this rule makes the warranty expire.
With the registers located on the front of the device, it is possible to adjust the heat emission of the same. They have to be opened according to
the calorific need. The best combustion (with minimum emissions) is reached when, by loading the wood, most part of the air for combustion
flows through the secondary air register.
Never overload the appliance. Too much fuel and too much air for the combustion may cause overheating and then damage
the product.
You should always use the appliance with the door closed in order to avoid damages due to overheating (forge effect).
The adjustment of the registers necessary to reach the rated calorific yield with a depression at the stack of 12 Pa (=1.2 mm of column of
water) is the following one: see chap. TECHNICAL DESCRIPTION. The appliance works as an intermittent operating appliance.
Besides the adjustment of the air for the combustion, the intensity of the combustion and consequently the thermal performance of the
device is influenced by the stack. A good draught of the stack requires a stricter adjustment of air for combustion, while a poor draught
requires a more precise adjustment of air for combustion.
To verify the good combustion, check whether the smoke coming out from the stack is transparent.
If it is white, it means that the device is not properly adjusted or the wood is too wet; if instead the smoke is gray or black, it signals that the
combustion is not complete (it is necessary a greater quantity of secondary air).
WARNINg: When fuel is added onto the embers in the absence of a flame, a considerable amount of fumes may develop. Should
this happen, an explosive mixture of gas and air may form, and in extreme cases an explosion may occur. For safety reasons it is
advisable to perform a new lighting procedure with the use of small strips.

OPERATION DURINg TRANsITION PERIODs

During transition periods when the external temperatures are higher, if there is a sudden increase of temperature it can happen that the
combustion gases inside the flue cannot be completely sucked up.
The exhaust gases do not come out completely (intense smell of gas). In this case, shake the grating more frequently and increase the air for
the combustion. Then, load a reduced quantity of fuel in order to permit a rapid burning (growing up of the flames) and the stabilization of
the draught.
Then, check that all openings for the cleaning and the connections to the stack are air-tight. In case of doubt, do not operate the
product.
Picture 9. Arrange the largest at the bottom and the smallest at the top,
Picture 9. Cross the four logs and place them on top of the pile of wood at
www.energia-legno.ch
ENgLIsH 27