Gymrex GR-SPB335 Manuel D'utilisation page 4

EN USER MANUAL
TECHNICAL DATA
Parameter Parameter value
description
Product Inflatable stand-up paddle board
name
Model GR- GR- GR- GR-
SPB335 SPB305 SPB340 SPB365
Maximum 145 135 145 230
load [kg]
Dimensions 335x 305x 335x 365x
[cm] 71x15 79x15 79x15 110x15
Air pressure 0.7- 0.7- 0.7- 0.7-0.97/
[bar]/[psi] 0.97/ 0.97/ 0.97/ 10-14
10-14 10-14 10-14
Weight 11 8 10 15.5
LEGEND
Read instructions before use.
Use a life jacket or other safety equipment to
help you stay afloat.
Do not jump into the water.
Keep the product away from sources of fire
and heat.
Do not leave the product in the sun; this has
a negative impact on product lifetime.
Pay attention to winds and currents. Do not use
in strong wind or open water.
Avoid contact of the product with sharp objects.
Product is intended for people who can swim.
Stay watched by other person while using the
product.
Maximum weight of a user shall not exceed
the value indicated in product's technical
parameters.
Product is allowed to be used by one adult
person at a time.
Maximum distance from the coast allowed while
using a product is 250 m.
Product is not designed for protection against
drowning.
Product shall be fully inflated before use.
Air pressure inside a product shall range from 0.7
to 0.97 bar (10÷14 PSI).
Product is not designed to be used on mountain
rivers.
Do not use a product on rough waters.
Do not use a product when wind speed exceeds
20hm/h.
Children below 12 years of age are not allowed
to use a product.
PLEASE NOTE! Drawings in this manual are for
illustration purposes only and in some details may
differ from the actual product.
The original operation manual is in German. Other
language versions are translations from German.
2. USAGE SAFETY
ATTENTION! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in an electric shock, fire and/
or serious injury or even death.
Whenever „device" or „product" are used in the warnings
and instructions, it shall mean <Inflatable stand-up paddle
board>.
1.1. Follow the instructions to assemble the product.
1.2. If in doubt whether the product works correctly or if
it is damaged, contact the manufacturer's customer
service.
1.3. Before each use make sure that the product is in
good technical condition.
1.4. Do not exceed the maximum load specified in the
specifications table.
1.5. Do not use a damaged product.
1.6. Do not alter any product parts or accessories.
1.7. Paddling in a standing position may pose hazards.
1.8. Be aware of the possibility of unforeseen dangers
when using the product.
1.9. The maximum permissible load on the board must
not be exceeded.
1.10. It is forbidden to use the product while under the
influence of intoxicants, alcohol or medication.
1.11. Use the board together with another experienced
user. Inform other users about your planned route
and the time of use of the board.
1.12. Before using the board, check the weather forecast
for the conditions in the aquatic environment
(winds can push the user towards open water, water
currents may make it difficult to mount the board,
etc.).
1.13. Do not use the board if the conditions in the aquatic
environment exceed the user's skills (high waves,
strong water currents, etc.).
1.14. The board should be used close to the shore
keeping in mind the changing weather conditions
(wind, tides, etc.).
1.15. It is forbidden to use the board during a storm and
on unknown body of water.
1.16. Do not exceed the maximum allowable pressure
when pumping up the board – this may damage the
board.
1.17. Always read the local regulations and the risks
associated with using the iSUP board.
2. USE GUIDELINES
Inflatable Stand Up Paddle Board is used for floating with
a paddle on the water. The product may only be used in
places and conditions for which it was intended.
6 7
The user is liable for any damage resulting from
nonintended use of the device.
2.1. PRODUCT DESCRIPTION/PREPARING FOR USE
6
1
5
1. iSUP board
2. pump
3. paddle
4. repair kit
5. ballast
6. bag
2.1.1. PUMPING AND INSTALLATION OF BALLAST
A
C
10~14PSI
E
A. Unfold the board
B. Connect the pump
C. Inflate without exceeding the maximum allowable
pressure (10-14 PSI)
D. Slide the ballast into the assembly place
E. Secure the ballast with a clip
F. The board is ready for use
Do not use the board in shallow water due to the risk of
damage to the ballast. Do not step on the board with the
mounted ballast while the board is on the ground.
2.1.2. DEFLATING THE BOARD AND DEINSTALLATION OF
THE BALLAST
A
2
C
2
3
4
E
A. Unlock the ballast by pulling out the clip
B. Take out the ballast
C. Pump out the air
D. Press to let out air
E. Fold the board
F. The board is prepared for storage/transport
2
B
2.1.3. VALVE
1
The plastic tip in the valve serves to evacuate the air if it is
in the lower position. The upper position of the tip is used
to inflate the air as well as to prevent air loss.
1. If the valve is leaking or if it is impossible to inflate
the board, check the position of the plastic tip – keep
D it in the upper position.
Pumping out – lower position of the tip:
F
1
Pumping the air – upper position of the tip
1
2. The valve may sometimes become loose, tighten it
with a wrench.
B
D
1
1
2
F
1. plastic tip
1. plastic tip
2
1