Water Dispenser - Whirlpool W10360467C Instructions D'installation

External Control Panel
■ To turn cooling off, press and hold both the Freezer Temp and
Fridge Temp buttons at the same time for 3 seconds. When
cooling is off, "Cooling Off" will appear on the display screen.
■ To turn cooling back on. Press and hold both the Freezer
Temp and Fridge Temp buttons at the same time for 3 seconds.
When cooling is on, "Cooling Off" will disappear and the
previously selected settings will appear on the display screen.
Additional Features
Door Open Alarm
■
The Door Open icon lights up whenever either door is opened.
■ When either door is open for 5 minutes and cooling is on, an
alert tone will sound three times, and the Door Open icon will
flash seven times. This pattern will repeat every 2 minutes until
all the doors are closed properly. The feature then resets and
will reactivate when either door is left open again for 5 minutes.
NOTES:
■ To mute the audible alarm while keeping the doors open,
such as while cleaning the inside of the refrigerator, press
any button on the control panel. The alarm sound will be
temporarily turned off, but the Door Open icon will still be
displayed on the dispenser control panel.
■ Both doors must be fully closed to turn off the Door
Open icon.
Fast Cool
The Fast Cool feature assists during times of high refrigerator use,
full grocery loads or temporarily warm room temperatures.
■ Press FAST COOL to set the freezer and refrigerator to
the coldest temperature settings. Press FAST COOL again
to return to the selected temperature set point.
NOTES:
■ The Fast Cool icon will be illuminated while the
refrigerator is in Fast Cool mode.
■
The Fast Cool feature will turn off automatically
after 24 hours.
Moisture Control
The moisture control feature turns on a heater to help reduce
moisture on the door hinge seal. Use in humid environments or
when you notice moisture on the door hinge seal. The refrigerator
uses more energy when Moisture Control is ON.
NOTE: The moisture control icon will light up to indicate the
feature is ON.
To turn on/off the moisture control feature:
■ Internal Control Panel - Press and hold MOISTURE
CONTROL for 3 seconds.
■
External Control Panel - Press and hold LIGHT for 3 seconds.
Water Filter Status Light and Reset
The filter reset control allows you to restart the water filter
status tracking feature each time you replace the water filter.
See "Water Filtration System."
■
Press and hold WATER FILTER for 3 seconds, to reset the
water filter status to Good. The water filter icon will turn blue.
Air Filter Status Light and Reset
The filter reset control allows you to restart the air filter status
tracking feature each time you replace the air filter. See "Install
Air Filter."
■
Press and hold AIR FILTER for 3 seconds, to reset the air filter
status to Good. The air filter icon will turn blue.

Water Dispenser

(on some models)
IMPORTANT:
■ Allow 3 hours for the refrigerator to cool down and chill water.
■ Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced.
■ The dispensing system will not operate when the
refrigerator door is open.
Flush the Water System
Air in the water dispensing system can cause the water dispenser
to drip. After connecting the refrigerator to a water source or
replacing the water filter, flush the water system.
Flushing the water dispensing system forces air from the water
line and filter and prepares the water filter for use. Additional
flushing may be required in some households.
NOTE: As air is cleared from the system, water may spurt out
of the dispenser.
1. Using a sturdy container, depress and hold the water dispenser
paddle for 5 seconds.
2. Release the dispenser paddle for 5 seconds.
3. Repeat steps 1 and 2 until water begins to flow.
4. Once water begins to flow, continue depressing and releasing
the dispenser paddle (5 seconds on, 5 seconds off) until a
total of 4 gal. (15 L) has been dispensed.
Dispense Water
IMPORTANT:
■
The dispensing system will not operate when the
refrigerator door is open.
■
The display screen on the dispenser control panel will turn off
automatically and enter "sleep" mode when the control buttons
and dispenser paddles have not been used for 2 minutes or
more. While in "sleep" mode, the first press of a control button
will only reactivate the display screen, without changing any
settings. After reactivation, changes to any settings can then be
made. If no changes are made within 2 minutes, the display will
re-enter "sleep" mode.
To dispense water:
1. Press a sturdy glass against the water dispenser paddle.
15