Bosch GSB 1600 RE Professional Notice Originale page 13

OBJ_BUCH-99-005.book Page 13 Thursday, May 22, 2014 12:56 PM
Impact Drill
Speed preselection
Right/left rotation
Spindle collar dia.
Max. drilling dia.
– Brickwork
– Concrete
– Steel
– Wood
Chuck clamping range
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-1.
Typically the A-weighted noise levels of the product are:
Sound pressure level 98 dB(A); Sound power level
109 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Drilling into metal: a = 2.7 m/s
h
Impact drilling into concrete: a = 23 m/s
h
Screwdriving without impact: a
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-1.
Bosch Power Tools
Technical file (2006/42/EC) at:
GSB 1600 RE
Robert Bosch GmbH, PT/ETM9,

70764 Leinfelden-Echterdingen, GERMANY

Henk Becker
mm 43
Executive Vice President
Engineering
mm 18
mm 16
mm 12
mm 30
Robert Bosch GmbH, Power Tools Division
mm 1.5–13
70764 Leinfelden-Echterdingen, GERMANY
07.05.14
kg 1.9
Assembly
/II
Auxiliary Handle (see figure A)
 Operate your machine only with the auxiliary handle
The auxiliary handle 12 can be set to any position for a secure
and low-fatigue working posture.
Turn the wing bolt for adjustment of the auxiliary handle 11 in
anticlockwise direction and set the auxiliary handle 12 to the
required position. Then tighten the wing bolt 11 again in
clockwise direction.
Adjusting the Drilling Depth (see figure A)
2
, K =1.5 m/s ,
The required drilling depth X can be set with the depth stop
2 2
, K =3.5 m/s ,
13.
2 2
<2.5 m/s , K =1.5 m/s .
Press the button for the depth stop adjustment 10 and insert
the depth stop into the auxiliary handle 12.
Pull out the depth stop until the distance between the tip of
the drill bit and the tip of the depth stop corresponds with the
desired drilling depth X.
Changing the Tool
 Before any work on the machine itself, pull the mains
Keyless Chuck (see figure B)
Hold the rear sleeve 3 of the keyless chuck 1 tight and turn the
front sleeve 2 in rotation direction , until the tool can be in-
serted. Insert the tool.
Hold the rear sleeve 3 of the keyless chuck 1 tight and firmly
turn the front sleeve 2 in rotation direction  by hand until
the locking action is no longer heard. This automatically locks
the drill chuck.
The locking is released again to remove the tool when the
front sleeve 2 is turned in the opposite direction.
Screwdriver Tools (see figure C)
When working with screwdriver bits 15, a universal bit holder
14 should always be used. Use only screwdriver bits that fit
the screw head.
For driving screws, always position the "Drilling/Impact Drill-
ing" selector switch 4 to the "Drilling" symbol.
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
12.
plug.
English | 13
1 609 92A 0NF | (22.5.14)