Briteq BT-250W Mode D'emploi page 6

ENGLISH
Tilt Inversion
Normal: Tilt movement is not inversed.
Tilt inversion: tilt movement is inversed
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select
(normal) or
 Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Led Display
Display on: display is always on.
Display off: display is off when not used.
 Press the MENU button until the display shows
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select
(display always on) or
 Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Display Inversion
Display normal: display is readable when the unit is on the floor.
Display inversion: display is readable when the unit is mounted upside down.
 Press the MENU button until
is blinking on the display. (normal display)
 Use the ENTER button to change to the mode
stored after 8 seconds. Or press the ENTER button again return to the mode
 To go back to the functions press the MENU button.
Self-Test
Used to activate the internal "self-test" program which shows all possibilities of the unit.
 Press the MENU button until
is blinking on the display.
 Press the ENTER button to start the internal self-test program.
 To go back to the functions press the MENU button.
Ambient temperature of lamp
Used to show the temperature inside the lamp compartment
 Press the MENU button until the
sign is blinking on the display.
 Press the ENTER button and the ambient temperature of lamp will show on the display.
 To go back to the functions press the MENU button again.
Fixture Hours
Used to show the number of working hours of the unit.
 Press the MENU button until
is blinking on the display.
 Press the ENTER button to show the number of working hours in the display.
 To go back to the functions press the MENU button.
BRITEQ
®
OPERATION MANUAL
(tilt inversion) mode.
.
(display off when not used).
(display inversion), the option will be automatically
(normal display).
7/64 BT-250W
ENGLISH
Lamp Display
Used to switch the lamp ON/OFF so you can cool the lamp with the internal fans before
transportation
 Press the MENU button until
is blinking on the display.
 Press ENTER button so the display starts blinking.
 Use DOWN and UP button to select the
 Once the mode is selected, press the ENTER button to setup
(or automatically return to the main functions without any change after 8 seconds)
 To go back to the functions without any change press the MENU button again.
Reset
Used to force a reset of the unit.
 Press the MENU button until
is blinking on the display.
 Press the ENTER to reset all channels to their standard position.
 To go back to the functions press the MENU button.
Please also check the chapter about the DMX-channel configuration of the unit to find out how you can force
a reset by DMX.
Home Position Adjust

Press MENU button for at least 5
seconds to go into offset mode

Now you can adjust the home
position ( this is the zero position )

The functions are shown below:
Pan offset

Press the MENU button for at least
5 seconds to activate offset mode

Use DOWN and UP button until
is shown on the display.

Press the ENTER button so the display starts blinking.

Use DOWN and UP button to adjust the pan home position.

Once the position has is selected, press the ENTER button to setup OR Automatically return to the offset
functions without any changes by pressing the MENU button

To go back to the main functions without any change wait 8 seconds.
Tilt offset

Press the MENU button for at least 5 seconds to activate offset mode

Use DOWN and UP button until is shown on the display.

Press the ENTER button so the display starts blinking.

Use DOWN and UP button to adjust the tilt home position.

Once the position has is selected, press the ENTER button to setup OR Automatically return to the offset
functions without any changes by pressing the MENU button

To go back to the main functions without any change wait 8 seconds.
BRITEQ
®
OPERATION MANUAL
(Lamp on) or (Lamp off) mode.
8/64 BT-250W