Bosch GSR 10,8-2-LI Professional Notice Originale page 15

OBJ_BUCH-970-003.book Page 15 Wednesday, July 27, 2011 3:35 PM
If the gear selector 3 cannot be pushed through to the stop,
lightly turn the drill chuck with drill.
Switching On and Off
To start the machine, press the On/Off switch 7 and keep it
pressed.
The power light 9 lights up when the On/Off switch 7 is slightly
or completely pressed, and allows the work area to be illumi-
nated when lighting conditions are insufficient.
To switch off the machine, release the On/Off switch 7.
Adjusting the Speed
The speed of the switched on power tool can be variably ad-
justed, depending on how far the On/Off switch 7 is pressed.
Light pressure on the On/Off switch 7 results in a low rotation-
al speed. Further pressure on the switch results in an increase
in speed.
Fully automatic spindle locking (Auto-lock)
When the On/Off switch 7 is not pressed, the drill spindle and
thus the tool holder are locked.
This enables screws to be screwed in, even when the battery
is empty and allows for the machine to be used as a screwdriv-
er.
Run-on Brake
When the On/Off switch 7 is released, the chuck brakes to a
stop, thus preventing the run-on of the tool.
When driving in screws, wait until the screw is screwed in
flush with the material and then release the On/Off switch 7.
By doing so, the head of the screw does not penetrate into the
material.
Battery Charge-control Indication
The battery charge-control indicator 8 consists of three green
LEDs, and indicates the charge condition of the battery for a
few seconds when the On/Off switch 7 is pressed halfway or
fully.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot be subject
to overload. When the load is too high or the allowable battery
temperature range of 0–70 °C is exceeded, the speed is re-
duced. The power tool will not run at full speed until reaching
the allowable battery temperature.
Working Advice
Apply the power tool to the screw only when it is
switched off. Rotating tool inserts can slip off.
After longer periods of working at low speed, allow the ma-
chine to cool down by running it for approx. 3 minutes at max-
imum speed with no load.
Bosch Power Tools
For drilling in metal, use only perfectly sharpened HSS drill
bits (HSS=high-speed steel). The appropriate quality is guar-
anteed by the Bosch accessories program.
Before screwing larger, longer screws into hard materials, it is
advisable to predrill a pilot hole with the core diameter of the
thread to approx.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
For safe and proper working, always keep the machine
and ventilation slots clean.
When the battery is no longer operative, please refer to an au-
thorised after-sales service agent for Bosch power tools.
If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by
an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
After-sales Service and Customer Assistance
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Our customer service representatives can answer your ques-
tions concerning possible applications and adjustment of
products and accessories.
Great Britain
Capacity
Robert Bosch Ltd. (B.S.C.)
≥ 2/3
P.O. Box 98
≥ 1/3
Broadwater Park
< 1/3
North Orbital Road
Denham
Reserve
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88
English | 15
2
/ of the screw length.
3
2 609 140 658 | (27.7.11)